I have same problem in generic build.
I configure to suspend the device when push power key, then it automatically power off the TV with CEC.
Sometimes, 5 minutes later it power on the device and TV. I don't understand why.
How could I get logs about it?
Regards.
It's probably for older devices using 3.10 kernel. Driver in 3.14 kernel is different.
OK.
If you want to could make some test with RAW data over CEC, but I don't know how yo start.
Regards.
I don't have solution for this either but if you find a guide created for other device, like RPi I think you should be able to use it - we also use libCEC for CEC communication (although hardware implementation is Amlogic-specific).
Thanks for the reply. I found this code: GitHub - gdachs/service.xbmc.amlogic-cec: CEC for amlogic devices
Could this code works with our devices?
Best regards.
CEC on Samsung TV's not working well with 009, have to check how it behaves with 008
Sent from my iPhone using Tapatalk
Hello, is there any shell command to test CEC?
My TV is not working too, it is a Sony TV.
I want to know if there id a command to power on/off the TV from LE.
Regards.
Direct answer: When I booted with android, went to settings, about, hardware: There was the model mxiii-2 and the processor specification s905x.
There was no sign externally, or in the box.But there were several "hints" that should have given it away easily: it came with android 6, and it didn't work in the first boot when I used the dtb.img of the s905 (no wifi, lan, usb...), pretty logical when you think about it.
I was not happy about it, I was looking for the s905 because I read here that the development was more advanced. On the other side in Amazon the mx-iii was 53€ while the mx-iii2 was 44€, so it also felt like I was scammed. The next day I cheked the mx-iii was "not available", so I guess they just send me that and didn't even know about it.
Regards
Thanks,
I don't have Android installed, could I check it in LE?
Regards.
Hello all,I have just registered, first I am not trying to troll or anything. I have been using XBMC for a long time, Kodi not so long, usually from Openelec, and more recently Libreelec.
I just wanted to explain my little (short) experience for a day with an s905x:
I have two home theaters at home, both with dedicated (silent) computers, 5.1 sound systems, and a Rpi3 on another single tv (yes, the kitchen).
I have been looking for some time for a simple, yet powerfule (x265) solution to use as a kodi player, after reading the forums I decided to get an s905 device Beelink MiniMXIII from amazon. And here the problems began...
I received the player next day, and installed the libreelec on an sdcard. It booted at first try (toothpick), but after loading nothing worked (no usb, no mouse, no controls, etc).
After digging a bit, I discover that although I specifically asked for an MXIII they sent me an MXIII-II, yes, same specs but with the s905x processor.
I remade the sdcard with the correct dtb.img and now I have a workable system. The usb's work, the ethernet too.
Here are my impressions:
wifi didn't work, ok, I can put an ethernet.
remote didn't work, ok, not the most important, and I also read in the forums you need to copy the correct config.
CEC remote (the one from tv, hdmi interface) didn't work either (the Rpi3 worked correctly with this tv)It's ok, I can get that.
Now the serious stuff. No matter what I did, no matter what I setup, I could not make it work in 5.1. The central (voice) channel was always mute.
I changed the libreelec version (7.2 and 7.9), change settings, tried with libreelec, tried with kodi from the android system... all of them failed in the same way. Stereo worked though, but that is not enough for me.
As a personal note, it also looked like the image didn't have the same quality as my x86 player (thay may have been my impression though).So my question is, had any one got any similar experience? I understand that the device is under heavy development (thanks kszaq!), and that I have only read half the messages in the post but I am curious to know if anyone has had more luck than me with the optical output.
I returned the device, I will keep an eye on the forum and for sure I will try again in the future, but the first impresssion was... very unsatisfactory.
Regards
PD: Sorry I am not providing logs, or more information about the tests I made.
Hello,
How did you know that it is a MXIII-II?
Maybe I have same device.
Regards.
Update to the latest alpha build and post back if it is still happening.
Hello,
Same happens in v7.90.007
Do you need some logs?
Regards
Do you set correct permissions?
chmod +x filename
Regards.
This is an old Sony TV.
I have the key codes in a lircd.conf. Years ago I have a Debian based HTPC and I could send the correct keys.
Now I want to know how to send thoose codes with commands in a Libreelec Kodi device.
And then assign some remote keys to thoose commands.
Kind regards.
Hello,
Anyone is using IR blaster for control (volume, input and power) the TV?
I have a MCE USB IR blaster, I want configure it to send commands to my TV to volume up/down and power on/off.
I have a lircd.conf with my TV remote keys. I want to map my LE remote volume keys for send IR commands to IR blaster.
Someone could help me?
Best regards.
I think that this is not supported.
Developer could confirm this.
Regards.
- Does suspend work?
- Do you have memory leak on playing videos (memory allocation problem)?
Suspend doesn't work.
Has anyone with mk808b pro (amlogic s905 stick) succeeded with installing LibreELEC to NAND?I just got this device yesterday. I can install LE (both kszaq's krypton and jarvis build) to sd card. But when tried ssh install to NAND it will fail to boot and then brick the device.
SSD command "installtointernal" was shown successfully flash to NAND. But it won't boot from NAND, instead it still boot to sd card. So I did ssh "installtointernal" a second time, this will get the device brick and can't boot from sd card anymore. I have to flash with amlogic burning tool to start all over again.
I did this twice, first time with krypton and second with jarvis, and it was all the same result,that is, the device will get brick after the second ssh install command.
Any possible solution for installing to NAND?
Try twice.
Thanks,
In the codesnake post video shows how to install the service.
Regards.
I think the easiest way for beginner is to setup tvheadend. There are several tutorials for WeTek Play available, just Google for them. For example this:External Content www.youtube.comContent embedded from external sources will not be displayed without your consent.Through the activation of external content, you agree that personal data may be transferred to third party platforms. We have provided more information on this in our privacy policy.
Thanks!
I have a tvheadend service installed in Linux PC and I know how to configure it.
How could I install the service?
Best regards.
Hello,
Yes, I have with tuner, but actually I don't use it. I wsnt to start to use to watch some satellite channels.
Sorry for my english.
Regards.
Hello,
I have LE alpha installed in a Wetek Play without DVB tuners, I use to play films and see pictures.
I have one DVB-S2 tuner for Wetek Play and I want to use it.
How could I configure channels? Need I install some addons?
Thanks and regards.
Hello,
I notice that this build could not scale the video in livetv channel list screen. It show the full screen video preview cuted instead of scaled.
This happens in S905, is it something with video decoding/hardware?
Best regards.
