LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
Manufacturer ID:0xff
CH0 RX Vref:27.5%, TX Vref:23.8%,0.0%
CH1 RX Vref:27.1%, TX Vref:22.8%,0.0%
CH2 RX Vref:29.7%, TX Vref:21.8%,0.0%
CH3 RX Vref:29.3%, TX Vref:21.8%,0.0%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-ge4e124926e-230922 #lxh (Sep 25 2023 - 10:58:38), fwver: v1.13
Trying to boot from MMC2
part_get_info_efi: *** ERROR: Invalid GPT ***
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
part_get_info_efi: *** ERROR: Invalid GPT ***
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
No misc partition
part_get_info_efi: *** ERROR: Invalid GPT ***
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
part_get_info_efi: *** ERROR: Invalid GPT ***
part_get_info_efi: *** ERROR: Invalid Backup GPT ***
spl: partition error
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(581130cddd...) + OK
## Checking uboot 0x00200000 ... sha256(ee573493b2...) + OK
## Checking fdt 0x00343ee8 ... sha256(60b3966c5c...) + OK
## Checking atf-2 0x000f0000 ... sha256(6a00298af8...) + OK
## Checking atf-3 0xff100000 ... sha256(71c3a5841b...) + OK
## Checking atf-4 0xff001000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(603cfbd25d...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 901.158/1055.866 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-364-g55ca4fb1c:derrick.huang
NOTICE:  BL31: Built : 12:00:02, May 13 2022
INFO:    timer_hp_init no valid 32k timer source, use normal mode
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    system boots from cpu-hwid-0
INFO:    idle_st=0x21fff, pd_st=0x11fff9
ERROR:   dfs get fsp_params[0] error, 0xfead0004 != 0xfead0001
ERROR:   dfs get fsp_params[1] error, 0x0 != 0xfead0001
ERROR:   dfs get fsp_params[2] error, 0x0 != 0xfead0001
ERROR:   dfs get fsp_params[3] error, 0x564 != 0xfead0001
ERROR:   loader&trust unmatch!!! Please update trust if need enable dmc
INFO:    BL31: Initialising Exception Handling Framework
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
INFO:    hdmirx_handler: dma not on, ret
I/TC: 
I/TC: OP-TEE version: 3.13.0-639-g8e053a881-dev #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon Mar 14 09:09:01 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-armbian (Mar 16 2023 - 10:18:31 +0300)

Model: Radxa ROCK 5B
PreSerial: 2, raw, 0xfeb50000
DRAM:  4 GiB
Sysmem: init
Relocation Offset: edb33000
Relocation fdt: eb9f8bb8 - eb9fecd0
CR: M/C/I
Using default environment

no mmc device at slot 1
mmc@fe2c0000: 1 (SD), mmc@fe2e0000: 0
Bootdev(atags): mmc 1
MMC1: Legacy, 52Mhz
PartType: DOS
DM: v2
No misc partition
boot mode: None
FIT: No boot partition
** Unable to read file /dtb.img **
No resource partition
No resource partition
No resource partition
Failed to load DTB, ret=-19
No find valid DTB, ret=-22
Failed to get kernel dtb, ret=-22
Unknown command 'gpio' - try 'help'
Model: Radxa ROCK 5B
CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
  b0pll 816000 KHz
  b1pll 816000 KHz
  lpll 816000 KHz
  v0pll 24000 KHz
  aupll 24000 KHz
  cpll 1500000 KHz
  gpll 1188000 KHz
  npll 24000 KHz
  ppll 1100000 KHz
  aclk_center_root 702000 KHz
  pclk_center_root 100000 KHz
  hclk_center_root 396000 KHz
  aclk_center_low_root 500000 KHz
  aclk_top_root 750000 KHz
  pclk_top_root 100000 KHz
  aclk_low_top_root 396000 KHz
No misc partition
Net:   No ethernet found.
Hit key to stop autoboot('CTRL+C'):  0 
starting USB...
Bus usb@fc800000: USB EHCI 1.00
Bus usb@fc840000: USB OHCI 1.0
Bus usb@fc880000: USB EHCI 1.00
Bus usb@fc8c0000: USB OHCI 1.0
Bus usb@fcd00000: usb maximum-speed not found
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@fc800000 for devices... 2 USB Device(s) found
scanning bus usb@fc840000 for devices... 1 USB Device(s) found
scanning bus usb@fc880000 for devices... 1 USB Device(s) found
scanning bus usb@fc8c0000 for devices... 1 USB Device(s) found
scanning bus usb@fcd00000 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
reading /extlinux/extlinux.conf
225 bytes read in 6 ms (36.1 KiB/s)
1:      LibreELEC
Retrieving file: /KERNEL
reading /KERNEL
86047232 bytes read in 6970 ms (11.8 MiB/s)
!!! env helper try: /uEnv.txt
Retrieving file: /uEnv.txt
** Unable to read file /uEnv.txt **
append: boot=LABEL=LIBREELEC disk=LABEL=STORAGE quiet console=ttyS2,1500000 console=tty0 systemd.debug_shell=ttyS2 coherent_pool=2M cec.debounce_ms=5000
Retrieving file: /dtb/rockchip/rk3588-rock-5b.dtb
reading /dtb/rockchip/rk3588-rock-5b.dtb
178470 bytes read in 28 ms (6.1 MiB/s)
Fdt Ramdisk skip relocation
No misc partition
## Flattened Device Tree blob at 0x0a100000
   Booting using the fdt blob at 0x0a100000
  'reserved-memory' shmem@10f000: addr=10f000 size=100
   Using Device Tree in place at 000000000a100000, end 000000000a12e925
can't found rockchip,drm-logo, use rockchip,fb-logo
WARNING: could not set reg FDT_ERR_BADOFFSET.
failed to reserve fb-loader-logo memory
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x1f0000000 - 0x200000000 (size: 0x10000000)
Total: 13751.899 ms

Starting kernel ...