▒
GXLX:BL1:9ac50e:4a8da0;FEAT:ADFC318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 139004

BL2 Built : 17:06:20, Sep 15 2017. gxl gf2da688 - xiaobo.gu@droid12

set vcck to 1070 mv
set vddee to 1070 mv
Board ID = 3
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 672MHz - FAIL
DDR3 chl: Rank0 @ 672MHz - PASS
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
Set ddr ssc: ppm1000-
-s
emmc switch 3 ok
Authentication key not yet programmed
emmc_rpmb_key_is_programmed: error 0x00000007
emmc switch 0 ok
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x0003c600
Load bl33 from eMMC, src: 0x00060200, des: 0x01000000, size: 0x00067c00
NOTICE:  BL3-1: v1.0(release):822871a
NOTICE:  BL3-1: Built : 14:38:30, Sep  8 2017
NOTICE:  BL31: GXL normal boot!
NOTICE:  BL31: BL33 decompress pass
mpu_config_enable:ok
[Image: gxl_v1.1.3255-1a77b01-dirty 2019-07-24 12:57:12 xiaosong.lin@droid13-sz]
OPS=0xc1
2b 90 9e 45 72 9e 4b 58 41 23 93 e0 [1.116567 Inits done]
secure task start!
high task start!
low task start!
ERROR:   Error initializing runtime service opteed_fast


U-Boot 2015.01-00053-gfdae34d5e0-dirty (Jun 16 2021 - 04:21:35)

DRAM:  1 GiB
Relocation Offset is: 36eae000
register usb cfg[0][1] = 0000000037f58cc8
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpu: vpu_clk_gate_init_off
vpp: vpp_init
boot_device_flag : 1
Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc.
init bus_cycle=6, bus_timing=7, system=5.0ns
reset failed
get_chip_type and ret:fffffffe
get_chip_type and ret:fffffffe
chip detect failed and ret:fffffffe
nandphy_init failed and ret=0xfffffff1
MMC:   aml_priv->desc_buf = 0x0000000033eae6b0
aml_priv->desc_buf = 0x0000000033eb09d0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
original ext_csd[171] USE_WP field value is 50
ext_csd[171] USER_WP filed value after switch is 58
init_part() 293: PART_TYPE_AML
[mmc_init] mmc init success
      Amlogic multi-dtb tool
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: p271 variant: 1g
        dtb 0 soc: gxl   plat: p271   vari: 1g
        dtb 1 soc: gxl   plat: p271   vari: 2g
      Find match dtb: 0
start dts,buffer=0000000033eb3200,dt_addr=0000000033eb3a00
      Amlogic multi-dtb tool
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: p271 variant: 1g
        dtb 0 soc: gxl   plat: p271   vari: 1g
        dtb 1 soc: gxl   plat: p271   vari: 2g
      Find match dtb: 0
parts: 10
00:      logo   0000000002000000 1
01:  recovery   0000000002000000 1
02:  cri_data   0000000000800000 1
03:       tee   0000000000800000 1
04:     param   0000000002000000 1
05:      misc   0000000002000000 1
06:      boot   0000000002000000 1
07:    system   0000000080000000 1
08:     cache   0000000020000000 2
09:      data   ffffffffffffffff 4
init_part() 293: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
hpd_state=0
cvbs performance type = 7, table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-917: calc 8eebfaa3, store 8eebfaa3
_verify_dtb_checksum()-917: calc 8eebfaa3, store 8eebfaa3
dtb_read()-1039: total valid 2
dtb_read()-1106: do nothing
      Amlogic multi-dtb tool
      Multi dtb detected
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: p271 variant: 1g
        dtb 0 soc: gxl   plat: p271   vari: 1g
        dtb 1 soc: gxl   plat: p271   vari: 2g
      Find match dtb: 0
gpio: pin GPIODV_27 (gpio 46) value is 1
Net:   dwmac.c9410000amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0

Start read misc partition datas!
info->attemp_times = 0
info->active_slot = 0
info->slot_info[0].bootable = 1
info->slot_info[0].online = 1
info->slot_info[1].bootable = 0
info->slot_info[1].online = 0
info->attemp_times = 0
attemp_times = 0
active slot = 0
wipe_data=successful
wipe_cache=successful
upgrade_step=2
[OSD]load fb addr from dts
[OSD]set initrd_high: 0x3fb00000
[OSD]fb_addr for logo: 0x3fb00000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3fb00000
[CANVAS]addr=0x3fb00000 width=3840, height=2160
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet
[KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet
InUsbBurn
noSof
Hit Enter or space or Ctrl+C key to stop autoboot -- :  0
card out
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
emmc/sd response timeout, cmd1, status=0x1ff2800
(Re)start USB...
USB0:   USB3.0 XHCI init start
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 0 **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Unrecognized filesystem type **
** Partition 13 not found on device 1 **
** Invalid partition 13 **
** Partition 14 not found on device 1 **
** Invalid partition 14 **
** Partition 15 not found on device 1 **
** Invalid partition 15 **
** Partition 16 not found on device 1 **
** Invalid partition 16 **
** Partition 17 not found on device 1 **
** Invalid partition 17 **
** Partition 18 not found on device 1 **
** Invalid partition 18 **
** Partition 19 not found on device 1 **
** Invalid partition 19 **
** Partition 20 not found on device 1 **
** Invalid partition 20 **
** Partition 21 not found on device 1 **
** Invalid partition 21 **
** Partition 22 not found on device 1 **
** Invalid partition 22 **
** Partition 23 not found on device 1 **
** Invalid partition 23 **
** Partition 24 not found on device 1 **
** Invalid partition 24 **
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f33450
copy done
Kernel command line: buildvariant=userdebug
load dtb from 0x1000000 ......
      Amlogic multi-dtb tool
      Single dtb detected
   Uncompressing Kernel Image ... OK
   kernel loaded at 0x01080000, end = 0x02258838
   Loading Ramdisk to 33d00000, end 33e9be6e ... OK
   Loading Device Tree to 000000001fff3000, end 000000001ffff3da ... OK
fdt_instaboot: no instaboot image

Starting kernel ...

uboot time: 4854678 us
domain-0 init dvfs: 4
[    0.000000@0] Reserved memory: unable to setup CMA region
[    0.194310@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    0.194333@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[    0.194548@0] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    0.194568@0] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[    0.204442@0] tv_vout: chrdev devno 266338304 for disp
[    0.696750@0] meson-pwm c1108550.meson-pwm: not support soc
[    0.696771@0] meson-pwm c1108550.meson-pwm: pwm_aml_parse_dt not support
[    0.696808@0] meson-pwm c1108550.meson-pwm: pwm_aml_probe not support
[    0.807112@0] mtdoops: mtd device (mtddev=name/number) must be supplied
[    0.817745@0] amlogic-new-usb3 d0078080.usb3phy: This phy has no usb port
[    0.823775@0] ATVR driver - init called!
[    0.905120@0] get_storage_dev return 1
[    1.066461@0] PPMGRDRV: err: ppmgr_driver_probe called
[    1.079089@0] get_storage_dev return 1
[    1.079118@0] aml_nand d0074800.nand: do not init nand
efuse_pw_en: 0x3
WARNING! efuse bits is disabled
Enable A53 JTAG to AO
[    1.322104@0] aml_snd_m8_card aml_m8_snd.46: ASoC: no source widget found for LOUTL
[    1.324111@0] aml_snd_m8_card aml_m8_snd.46: ASoC: Failed to add route LOUTL -> direct -> Ext Spk
[    1.332995@0] aml_snd_m8_card aml_m8_snd.46: ASoC: no source widget found for LOUTR
[    1.340593@0] aml_snd_m8_card aml_m8_snd.46: ASoC: Failed to add route LOUTR -> direct -> Ext Spk
[ ▒[    1.534856@3] init: property_set("ro.boot.serialno", "11b09c141") failed
[    1.611696@3] init: waitpid failed: No child processes
[    1.617454@3] init: /init.amlogic.rc: 275: chmod requires 2 arguments
[    1.630198@1] init: insmod: open("/boot/optee.ko") failed: No such file or directory
[    1.632215@0] init: insmod: open("/boot/optee_armtz.ko") failed: No such file or directory[    2.608348@2] init: enter do_confirm_formated /dev/block/tee, /tee
[    2.608901@2] init: blocksize 1024, bytes_per_inode 1024
[    2.614285@2] init: do_confirm_formated ext4 try mount
[    2.848671@1] accelerate:
[    2.848671@1] kernel start with quiet!
Hello Jten!!!
Hello Jten!!!
Hello Jten!!!