[3088]HELLO! BOOT0 is starting!
[3091]BOOT0 commit : 904a4b2
[3094]set pll start
[3096]periph0 has been enabled
[3100]set pll end
[3101]unknow PMU
[3103]PMU: AXP806
[3110]vaild para:8  select dram para2
[3114]board init ok
[3116]DRAM BOOT DRIVE INFO: V0.60
[3119]the chip id is 0x5d00
[3122]chip id check OK
[3125]DRAM_VCC set to 1200 mv
[3130][AUTO DEBUG]32bit,2 ranks training success!
[3140]DRAM CLK =720 MHZ
[3142]DRAM Type =7 (3:DDR3,4:DDR4,7:LPDDR3,8:LPDDR4)
[3150]Actual DRAM SIZE =1024 M
[3153]DRAM SIZE =1024 MBytes, para1 = 30ea, para2 = 4001000, dram_tpr13 = 6061
[3166]DRAM simple test OK.
[3168]rtc standby flag is 0x0, super standby flag is 0x0
[3174]dram size =1024
[3177]card no is 2
[3179]sdcard 2 line count 8
[3182][mmc]: mmc driver ver 2019-12-19 10:41
[3186][mmc]: set f_max to 50M, set f_max_ddr to 50M
[3191][mmc]: mmc 2 bias 4
[3199][mmc]: ***Try MMC card 2***
[3216][mmc]: MMC 5.0
[3218][mmc]: HSDDR52/DDR50 8 bit
[3221][mmc]: 50000000 Hz
[3224][mmc]: 7296 MB
[3226][mmc]: ***SD/MMC 2 init OK!!!***
[3288]Loading boot-pkg Succeed(index=0).
[3292]Entry_name        = u-boot
[3301]Entry_name        = monitor
[3305]Entry_name        = dtbo
[3308]Entry_name        = dtb
[3312]tunning data addr:0x4a0003e8
[3315]Jump to second Boot.
NOTICE:  BL3-1: v1.0(debug):cfcc355
NOTICE:  BL3-1: Built : 19:08:45, 2020-11-17
NOTICE:  BL3-1 commit: 8
ERROR:   Error initializing runtime service tspd_fast
NOTICE:  BL3-1: Preparing for EL3 exit to normal world
NOTICE:  BL3-1: Next image address = 0x4a000000
NOTICE:  BL3-1: Next image spsr = 0x1d3


U-Boot 2018.05 (May 14 2021 - 10:23:10 +0800) Allwinner Technology

[03.389]CPU:   Allwinner Family
[03.392]Model: sun50iw9
I2C:   ready
[03.397]DRAM:  1 GiB
[03.399]Relocation Offset is: 35ec5000
[03.437]secure enable bit: 0
[03.439]pmu_axp152_probe pmic_bus_read fail
[03.444]PMU: AXP806
[03.448]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=400Mhz
[03.635]sunxi overlay merged okqv
[03.638]drv_disp_init
[03.668]__clk_enable: clk is null.
[03.674]drv_disp_init finish
[03.677]gic: sec monitor mode
[03.700]flash init start
[03.702]workmode = 0,storage type = 2
[03.705]MMC:	 2
[03.707]get mem for descripter OK !
[03.716]get sdc2 sdc_boot0_sup_1v8 fail.
[03.720]io is 1.8V

[03.746]sunxi flash init ok
[03.749]Loading Environment from SUNXI_FLASH... OK
[03.760]usb burn from boot
delay time 0
weak:otg_phy_config
[03.773]usb prepare ok
[04.576]overtime
[04.580]do_burn_from_boot usb : no usb exist
[04.584]boot_gui_init:start
FAT: Misaligned buffer address (7be81e78)
32 bytes read in 4 ms (7.8 KiB/s)
[04.718]boot_gui_init:finish
[04.721]bmp_name=bootlogo.bmp
3686456 bytes read in 34 ms (103.4 MiB/s)
[04.769]hsddr 2-50000000
[04.771]hs200 5-200000000
[04.773]get max-frequency ok 100000000 Hz
[04.777]0 1 0: 0 1 0
[04.779]delete mmc-hs400-1_8v from dtb
[04.785]update dts
** Unrecognized filesystem type **
[04.797]load file(ULI/factory/rootwait init.txt) error.
** Unrecognized filesystem type **
[04.813]load file(ULI/factory/snum.txt) error.
[04.817]name in map mac
** Unrecognized filesystem type **
[04.830]load file(ULI/factory/wifi_mac.txt) error.
** Unrecognized filesystem type **
[04.844]load file(ULI/factory/bt_mac.txt) error.
** Unrecognized filesystem type **
[04.859]load file(ULI/factory/selinux.txt) error.
** Unrecognized filesystem type **
[04.874]load file(ULI/factory/specialstr.txt) error.
[04.906]update part info
[04.924]update bootcmd
[04.926]No ethernet found.
Hit any key to stop autoboot:  0 
[05.166]Starting kernel ...

[05.169]mmc exit start
[05.186]mmc 2 exit ok
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.170 (akrd6@R740XD) (gcc version 5.3.1 20160412 (Linaro GCC 5.3-2016.05) ) #11 SMP PREEMPT Wed May 5 13:32:43 CST 2021
[    0.000000] Boot CPU: AArch64 Processor [410fd034]
[    0.000000] bootconsole [earlycon0] enabled
[    0.027822] BOOTEVENT:        27.806624: ON
[    0.265554] sunxi_i2c_probe()2209 - [i2c3] warning: failed to get regulator id
[    0.266575] sunxi_i2c_probe()2209 - [i2c5] warning: failed to get regulator id
[    0.319810] acx00_i2c_probe,l:282
[    0.319950] [ac200] pwm is NULL! Just initialize it.
[    0.320842] [ac200] pwm enable
[    0.320879] [ac200] pwm is initialized
[    0.320943] acx00_init_work,l:130
[    0.321667] acx00_init_work,l:137
[    0.322149] sunxi_i2c_do_xfer()1935 - [i2c5] incomplete xfer (status: 0x20, dev addr: 0x10)
[    0.327956] [ac200] get ave_regulator_name failed!
[    0.423279] gpio_pin_4(229) gpio_request fail
[  [    0.428950] uart uart1: get regulator failed
[    0.461718] [NAND][NE] Not found valid nand node on dts
[    0.470263] sunxi-wlan soc@03000000:wlan: get gpio chip_en failed
[    0.477181] sunxi-wlan soc@03000000:wlan: get gpio power_en failed
[    0.615662] hci: request ohci1-controller gpio:232
[    0.807309] axp2101_pek: axp2101-pek can not register without irq
[    0.817680] sunxi_ir_startup: get ir protocol failed
[    0.825983] VE: get debugfs_mpp_root is NULL, please check mpp
[    0.825983] 
[    0.834358] VE: sunxi ve debug register driver failed!
[    0.834358] 
[    0.849779] mmc:failed to get gpios
[    0.929341] mmc:failed to get gpios
[    0.967528] FD655: ==fd655_driver_probe====================
[    0.973900] FD655: : (null)
[    0.977122] FD655: : (null)
[    0.980286] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RTO !!
[    0.986299] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RTO !!
[    0.995973] FD655: register_fd655_driver: Successed to add fd655  module 
[    1.003650] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !!
[    1.009583] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !!
[    1.015486] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !!
[    1.021393] sunxi-mmc sdc1: smc 2 p1 err, cmd 5, RTO !!
[    1.041832] failed get gpio-spdif gpio from dts,spdif_gpio:-2
[    1.050373] [sunxi_internal_codec_probe]:get audio avcc failed
[    1.057039] [sunxi_internal_codec_probe]:get audio vcc3v3-audio failed
[    1.064695] [audio-codec]dachpf_cfg configurations missing or invalid.
[    1.072070] lineout_vol:26, linein_gain:3, fmin_gain:3, digital_vol:0, adcdrc_cfg:0, adchpf_cfg:0, dacdrc_cfg:0, dachpf_cfg:0, ramp_func_used:1, pa_msleep_time:160, pa_ctl_level:0, gpio-spk:0
[    1.096021] sndhdmi sndhdmi: ASoC: CPU DAI (null) not registered
[    1.102847] sndhdmi sndhdmi: snd_soc_register_card() failed: -517
[    1.116469] sunxi-ahub-cpudai 5097000.cpudai3-controller: ahub cpudai id invalid
[    1.150036] ERROR: pinctrl_get for HDMI2.0 DDC fail
[    1.163414] tv_probe()1435 - of_property_read_string tv_power failed!
[    1.171670] tv_probe()1435 - of_property_read_string tv_power failed!
[    1.252671] cpu cpu1: opp_list_debug_create_link: Failed to create link
[    1.260192] cpu cpu1: _add_opp_dev: Failed to register opp debugfs (-12)
[    1.267825] cpu cpu2: opp_list_debug_create_link: Failed to create link
[    1.275296] cpu cpu2: _add_opp_dev: Failed to register opp debugfs (-12)
[    1.282894] cpu cpu3: opp_list_debug_create_link: Failed to create link
[    1.290358] cpu cpu3: _add_opp_dev: Failed to register opp debugfs (-12)
[    1.923979] selinux: avc:  denied  { set } for  scontext=u:r:vendor_init:s0 tcontext=u:object_r:default_prop:s0 tclass=property_service permissive=1
[    1.923979] 
[    1.941432] selinux: avc:  denied  { set } for  scontext=u:r:vendor_init:s0 tcontext=u:object_r:vold_prop:s0 tclass=property_service permissive=1
[    1.941432] 
[    1.959039] selinux: avc:  denied  { set } for  scontext=u:r:vendor_init:s0 tcontext=u:object_r:dalvik_prop:s0 tclass=property_service permissive=1
[    1.959039] 
[    2.860405] FAT-fs (mmcblk0p15): bogus number of reserved sectors
console:/ $ [    5.205867] apexd: Failed to walk /product/apex : Can't open /product/apex for reading : No such file or directory
[    6.877235] init: couldn't write 1890 to /dev/cpuset/camera-daemon/tasks: No such file or directory
[    7.807134] sunxi-mmc sdc0: smc 1 p0 err, cmd 8, RE !!
[    7.813306] sunxi-mmc sdc0: smc 1 p0 err, cmd 55, RE !!
[    7.819510] sunxi-mmc sdc0: smc 1 p0 err, cmd 55, RE !!
[    7.825731] sunxi-mmc sdc0: smc 1 p0 err, cmd 55, RE !!
[    7.831952] sunxi-mmc sdc0: smc 1 p0 err, cmd 55, RE !!
[    7.837889] mmc1: error -110 whilst initialising SD card
[   23.047474] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RTO !!
[   23.097533] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RTO !!
[   23.108348] sunxi-mmc sdc1: smc 2 p1 err, cmd 8, RTO !!
[   23.179237] SSV6XXX_SDIO mmc2:0001:1: vendor = 0x3030 device = 0x3030
[   23.210810] SSV6XXX_SDIO mmc2:0001:1: dataIOPort 0x10000 regIOPort 0x10020
[   23.221049] sunxi-mmc sdc1: smc 2 p1 err, cmd 52, RE RCE !!
[   23.299810] SSV6XXX_SDIO mmc2:0001:1: dataIOPort 0x10000 regIOPort 0x10020
[   23.342509] SSV6XXX HCI TX Task started.
[   23.388410] Enable HCI TX aggregation
[   24.372220] SSV WLAN driver SSV6006C: Set new macaddr
[   24.382183] SSV WLAN driver SSV6006C: VIF 14:b2:e5:d2:ab:42 of type 2 is added.
[   25.360851] SSV WLAN driver SSV6006C: Set new macaddr
[   25.367897] SSV WLAN driver SSV6006C: VIF 14:b2:e5:d2:ab:43 of type 2 is added.
[   26.075888] audit: rate limit exceeded
[   29.184326] audit: rate limit exceeded


console:/ $ [   35.939998] apexd: Can't open /product/apex for reading : No such file or directory
[   35.963246] SSV WLAN driver SSV6006C: Set key VIF 0 VIF type 2 STA 0 algorithm = 4, key->keyidx = 0, cmd = 0
[   35.990286] SET KEY 0
[   35.998581] SSV WLAN driver SSV6006C: Set key VIF 0 VIF type 2 STA -1 algorithm = 3, key->keyidx = 1, cmd = 0
[   36.013057] SET KEY 0
[   36.121860] IEEE80211_AMPDU_RX_START 90:8D:78:61:3E:CC 0.