[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.154 (jenkins@tsuboi) (gcc version 8.3.0 (GNU Toolchain for the A-profile Architecture 8.3-2019.03 (arm-rel-8.36)) ) #1 SMP Tue Mar 3 21:39:16 CET 2020 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '') [ 0.000000] bootconsole [uart0] enabled [ 0.000000] cma: Reserved 64 MiB at 0x00000000f1c00000 [ 0.000000] On node 0 totalpages: 1015296 [ 0.000000] DMA zone: 15864 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 1015296 pages, LIFO batch:31 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc0f7ed7000 s45864 r8192 d31960 u86016 [ 0.000000] pcpu-alloc: s45864 r8192 d31960 u86016 alloc=21*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 999432 [ 0.000000] Kernel command line: usbcore.autosuspend=-1 boot=UUID=2211-5513 disk=UUID=a321c910-4860-4321-bec0-31d20884f00c quiet console=uart8250,mmio32,0xff1a0000 console=tty0 earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.000000] software IO TLB [mem 0xf7e8f000-0xf7ecf000] (0MB) mapped at [ffffffc0f7e8f000-ffffffc0f7ecefff] [ 0.000000] Memory: 3902972K/4061184K available (9214K kernel code, 1284K rwdata, 5292K rodata, 2880K init, 669K bss, 92676K reserved, 65536K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 GB) [ 0.000000] .init : 0xffffff8008eb0000 - 0xffffff8009180000 ( 2880 KB) [ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008980000 ( 9216 KB) [ 0.000000] .rodata : 0xffffff8008980000 - 0xffffff8008eb0000 ( 5312 KB) [ 0.000000] .data : 0xffffff8009180000 - 0xffffff80092c1008 ( 1285 KB) [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum) [ 0.000000] 0xffffffbdc0008000 - 0xffffffbdc3e00000 ( 61 MB actual) [ 0.000000] fixed : 0xffffffbffe7fb000 - 0xffffffbffec00000 ( 4116 KB) [ 0.000000] PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 MB) [ 0.000000] memory : 0xffffffc000200000 - 0xffffffc0f8000000 ( 3966 MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000 [ 0.000000] ITS: allocated 65536 Devices @280000 (psz 64K, shr 0) [ 0.000000] ITS: using cache flushing for cmd queue [ 0.000000] GIC: using LPI property table @0x0000000000300000 [ 0.000000] ITS: Allocated 1792 chunks for LPIs [ 0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000 [ 0.000000] CPU0: using LPI pending table @0x0000000000310000 [ 0.000000] GIC: using cache flushing for LPI property table [ 0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] } [ 0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] } [ 0.000000] rockchip_mmc_get_phase: invalid clk rate [ 0.000000] rockchip_mmc_get_phase: invalid clk rate [ 0.000000] rockchip_mmc_get_phase: invalid clk rate [ 0.000000] rockchip_mmc_get_phase: invalid clk rate [ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work [ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work [ 0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31 [ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.001358] Console: colour dummy device 80x25 [ 0.001372] console [tty0] enabled [ 0.001380] bootconsole [uart0] disabled [ 0.001408] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000) [ 0.001420] pid_max: default: 32768 minimum: 301 [ 0.001569] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.001581] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) [ 0.002368] Initializing cgroup subsys io [ 0.002388] Initializing cgroup subsys memory [ 0.002420] Initializing cgroup subsys devices [ 0.002434] Initializing cgroup subsys freezer [ 0.002447] Initializing cgroup subsys pids [ 0.002473] ftrace: allocating 34983 entries in 137 pages [ 0.091178] sched-energy: Sched-energy-costs installed from DT [ 0.091195] CPU0: update cpu_capacity 401 [ 0.091254] ASID allocator initialised with 32768 entries [ 0.094203] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created [ 0.094704] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created [ 0.096012] Detected VIPT I-cache on CPU1 [ 0.096045] CPU1: found redistributor 1 region 0:0x00000000fef20000 [ 0.096075] CPU1: using LPI pending table @0x00000000eed10000 [ 0.096121] CPU1: update cpu_capacity 401 [ 0.096125] CPU1: Booted secondary processor [410fd034] [ 0.096658] Detected VIPT I-cache on CPU2 [ 0.096679] CPU2: found redistributor 2 region 0:0x00000000fef40000 [ 0.096707] CPU2: using LPI pending table @0x00000000eed40000 [ 0.096735] CPU2: update cpu_capacity 401 [ 0.096738] CPU2: Booted secondary processor [410fd034] [ 0.097294] Detected VIPT I-cache on CPU3 [ 0.097314] CPU3: found redistributor 3 region 0:0x00000000fef60000 [ 0.097341] CPU3: using LPI pending table @0x00000000eed90000 [ 0.097367] CPU3: update cpu_capacity 401 [ 0.097370] CPU3: Booted secondary processor [410fd034] [ 0.097890] Detected PIPT I-cache on CPU4 [ 0.097918] CPU4: found redistributor 100 region 0:0x00000000fef80000 [ 0.097959] CPU4: using LPI pending table @0x00000000eedc0000 [ 0.097997] CPU4: update cpu_capacity 1024 [ 0.098000] CPU4: Booted secondary processor [410fd082] [ 0.098536] Detected PIPT I-cache on CPU5 [ 0.098553] CPU5: found redistributor 101 region 0:0x00000000fefa0000 [ 0.098590] CPU5: using LPI pending table @0x00000000eedf0000 [ 0.098616] CPU5: update cpu_capacity 1024 [ 0.098619] CPU5: Booted secondary processor [410fd082] [ 0.098704] Brought up 6 CPUs [ 0.098786] SMP: Total of 6 processors activated. [ 0.098795] CPU features: detected feature: GIC system register CPU interface [ 0.098807] CPU: All CPU(s) started at EL2 [ 0.098854] alternatives: patching kernel code [ 0.100167] devtmpfs: initialized [ 0.117590] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns [ 0.117613] futex hash table entries: 2048 (order: 5, 131072 bytes) [ 0.119350] pinctrl core: initialized pinctrl subsystem [ 0.119626] regulator-dummy: no parameters [ 0.120223] NET: Registered protocol family 16 [ 0.131431] cpuidle: using governor ladder [ 0.141433] cpuidle: using governor menu [ 0.141565] vdso: 2 pages (1 code @ ffffff8008986000, 1 data @ ffffff8009184000) [ 0.141597] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.143035] DMA: preallocated 2048 KiB pool for atomic allocations [ 0.157596] gpiochip_add_data: registered GPIOs 0 to 31 on device: gpio0 [ 0.157670] gpiochip_add_data: registered GPIOs 32 to 63 on device: gpio1 [ 0.157743] gpiochip_add_data: registered GPIOs 64 to 95 on device: gpio2 [ 0.157812] gpiochip_add_data: registered GPIOs 96 to 127 on device: gpio3 [ 0.157884] gpiochip_add_data: registered GPIOs 128 to 159 on device: gpio4 [ 0.173680] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/dc-12v[0]' [ 0.173706] dc_12v: 12000 mV [ 0.173880] reg-fixed-voltage dc-12v: dc_12v supplying 12000000uV [ 0.174114] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc3v3-pcie-regulator[0]' - status (0) [ 0.174161] reg-fixed-voltage vcc3v3-pcie-regulator: Looking up vin-supply from device tree [ 0.174209] vcc3v3_pcie: supplied by dc_12v [ 0.174218] dc_12v: could not add device link regulator.2 err -2 [ 0.174259] vcc3v3_pcie: 3300 mV [ 0.174410] reg-fixed-voltage vcc3v3-pcie-regulator: vcc3v3_pcie supplying 3300000uV [ 0.174465] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc1v8-s0[0]' [ 0.174481] vcc1v8_s0: 1800 mV [ 0.174625] reg-fixed-voltage vcc1v8-s0: vcc1v8_s0 supplying 1800000uV [ 0.174675] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-sys[0]' [ 0.174692] reg-fixed-voltage vcc-sys: Looking up vin-supply from device tree [ 0.174726] vcc_sys: supplied by dc_12v [ 0.174734] dc_12v: could not add device link regulator.4 err -2 [ 0.174772] vcc_sys: 5000 mV [ 0.174938] reg-fixed-voltage vcc-sys: vcc_sys supplying 5000000uV [ 0.174988] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc-phy-regulator[0]' [ 0.175004] vcc_phy: no parameters [ 0.175152] reg-fixed-voltage vcc-phy-regulator: vcc_phy supplying 0uV [ 0.175207] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/vcc3v3-sys[0]' [ 0.175228] reg-fixed-voltage vcc3v3-sys: Looking up vin-supply from device tree [ 0.175263] vcc3v3_sys: supplied by vcc_sys [ 0.175272] vcc_sys: could not add device link regulator.6 err -2 [ 0.175300] vcc3v3_sys: 3300 mV [ 0.175445] reg-fixed-voltage vcc3v3-sys: vcc3v3_sys supplying 3300000uV [ 0.175584] of_get_named_gpiod_flags: parsed 'gpio' property of node '/vcc5v0-host-regulator[0]' - status (0) [ 0.175625] vcc5v0_host: no parameters [ 0.175786] reg-fixed-voltage vcc5v0-host-regulator: vcc5v0_host supplying 0uV [ 0.176372] iommu: Adding device ff650000.vpu_service to group 0 [ 0.176445] iommu: Adding device ff660000.rkvdec to group 1 [ 0.176514] iommu: Adding device ff670000.iep to group 2 [ 0.176614] iommu: Adding device ff900000.vop to group 3 [ 0.177375] rk_iommu ff670800.iommu: can't get aclk [ 0.177386] rk_iommu ff670800.iommu: can't get hclk [ 0.177894] SCSI subsystem initialized [ 0.178063] usbcore: registered new interface driver usbfs [ 0.178108] usbcore: registered new interface driver hub [ 0.178217] usbcore: registered new device driver usb [ 0.178359] pps_core: LinuxPPS API ver. 1 registered [ 0.178365] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.178384] PTP clock support registered [ 0.179637] Advanced Linux Sound Architecture Driver Initialized. [ 0.180142] Bluetooth: Core ver 2.21 [ 0.180169] NET: Registered protocol family 31 [ 0.180176] Bluetooth: HCI device and connection manager initialized [ 0.180189] Bluetooth: HCI socket layer initialized [ 0.180198] Bluetooth: L2CAP socket layer initialized [ 0.180221] Bluetooth: SCO socket layer initialized [ 0.180555] cfg80211: World regulatory domain updated: [ 0.180563] cfg80211: DFS Master region: unset [ 0.180568] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 0.180578] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 0.180587] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 0.180594] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 0.180602] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 0.180611] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 0.180618] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 0.180625] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 0.180632] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 0.181240] clocksource: Switched to clocksource arch_sys_counter [ 0.223028] FS-Cache: Loaded [ 0.231216] thermal thermal_zone1: power_allocator: sustainable_power will be estimated [ 0.231347] NET: Registered protocol family 2 [ 0.231782] TCP established hash table entries: 32768 (order: 6, 262144 bytes) [ 0.232046] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes) [ 0.232859] TCP: Hash tables configured (established 32768 bind 32768) [ 0.232972] UDP hash table entries: 2048 (order: 5, 196608 bytes) [ 0.233128] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes) [ 0.233510] NET: Registered protocol family 1 [ 0.233823] RPC: Registered named UNIX socket transport module. [ 0.233831] RPC: Registered udp transport module. [ 0.233836] RPC: Registered tcp transport module. [ 0.233841] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.233862] PCI: CLS 0 bytes, default 64 [ 0.326975] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 0.327067] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available [ 0.338247] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.338911] FS-Cache: Netfs 'nfs' registered for caching [ 0.339318] NFS: Registering the id_resolver key type [ 0.339344] Key type id_resolver registered [ 0.339350] Key type id_legacy registered [ 0.339370] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.339588] FS-Cache: Netfs 'cifs' registered for caching [ 0.344474] NET: Registered protocol family 38 [ 0.344507] Key type asymmetric registered [ 0.344520] Asymmetric key parser 'x509' registered [ 0.344705] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.344858] io scheduler noop registered [ 0.344870] io scheduler deadline registered [ 0.344909] io scheduler cfq registered (default) [ 0.345876] phy phy-ff770000.syscon:usb2-phy@e460.0: Looking up phy-supply from device tree [ 0.345975] vcc5v0_host: could not add device link phy-ff770000.syscon:usb2-phy@e460.0 err -2 [ 0.346277] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up phy-supply from device tree [ 0.346288] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed [ 0.346500] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up vbus-supply from device tree [ 0.346511] phy phy-ff770000.syscon:usb2-phy@e460.1: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e460/otg-port failed [ 0.346523] phy phy-ff770000.syscon:usb2-phy@e460.1: Failed to get VBUS supply regulator [ 0.347456] phy phy-ff770000.syscon:phy@f780.2: Looking up phy-supply from device tree [ 0.347466] phy phy-ff770000.syscon:phy@f780.2: Looking up phy-supply property in node /syscon@ff770000/phy@f780 failed [ 0.348499] phy phy-ff800000.phy.3: Looking up phy-supply from device tree [ 0.348510] phy phy-ff800000.phy.3: Looking up phy-supply property in node /phy@ff800000/dp-port failed [ 0.348604] phy phy-ff800000.phy.4: Looking up phy-supply from device tree [ 0.348613] phy phy-ff800000.phy.4: Looking up phy-supply property in node /phy@ff800000/usb3-port failed [ 0.348931] phy phy-pcie-phy.5: Looking up phy-supply from device tree [ 0.348941] phy phy-pcie-phy.5: Looking up phy-supply property in node /pcie-phy failed [ 0.350725] rockchip-pcie f8000000.pcie: GPIO lookup for consumer ep [ 0.350735] rockchip-pcie f8000000.pcie: using device tree for GPIO lookup [ 0.350763] of_get_named_gpiod_flags: parsed 'ep-gpios' property of node '/pcie@f8000000[0]' - status (0) [ 0.350996] rockchip-pcie f8000000.pcie: Looking up vpcie3v3-supply from device tree [ 0.351097] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply from device tree [ 0.351108] rockchip-pcie f8000000.pcie: Looking up vpcie1v8-supply property in node /pcie@f8000000 failed [ 0.351121] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found [ 0.351129] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply from device tree [ 0.351138] rockchip-pcie f8000000.pcie: Looking up vpcie0v9-supply property in node /pcie@f8000000 failed [ 0.351149] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found [ 0.371275] rockchip-pcie f8000000.pcie: invalid power supply [ 0.407635] PCI host bridge /pcie@f8000000 ranges: [ 0.407656] MEM 0xfa000000..0xfbdfffff -> 0xfa000000 [ 0.407666] IO 0xfbe00000..0xfbefffff -> 0xfbe00000 [ 0.407983] rockchip-pcie f8000000.pcie: PCI host bridge to bus 0000:00 [ 0.407995] pci_bus 0000:00: root bus resource [bus 00-1f] [ 0.408005] pci_bus 0000:00: root bus resource [mem 0xfa000000-0xfbdfffff] [ 0.408015] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfbe00000-0xfbefffff]) [ 0.408048] pci 0000:00:00.0: [1d87:0100] type 01 class 0x060400 [ 0.408148] pci 0000:00:00.0: supports D1 [ 0.408156] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.408399] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.408517] pci_bus 0000:01: busn_res: can not insert [bus 01-ff] under [bus 00-1f] (conflicts with (null) [bus 00-1f]) [ 0.408549] pci 0000:01:00.0: [1b21:0612] type 00 class 0x010601 [ 0.408591] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 0.408599] pci 0000:01:00.0: reg 0x10: [io size 0x0008] [ 0.408615] pci 0000:01:00.0: reg 0x14: initial BAR value 0x00000000 invalid [ 0.408622] pci 0000:01:00.0: reg 0x14: [io size 0x0004] [ 0.408637] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid [ 0.408644] pci 0000:01:00.0: reg 0x18: [io size 0x0008] [ 0.408659] pci 0000:01:00.0: reg 0x1c: initial BAR value 0x00000000 invalid [ 0.408666] pci 0000:01:00.0: reg 0x1c: [io size 0x0004] [ 0.408680] pci 0000:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid [ 0.408687] pci 0000:01:00.0: reg 0x20: [io size 0x0020] [ 0.408703] pci 0000:01:00.0: reg 0x24: [mem 0x00000000-0x000001ff] [ 0.408719] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.414607] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.414640] pci 0000:00:00.0: BAR 8: assigned [mem 0xfa000000-0xfa0fffff] [ 0.414653] pci 0000:01:00.0: BAR 6: assigned [mem 0xfa000000-0xfa00ffff pref] [ 0.414662] pci 0000:01:00.0: BAR 5: assigned [mem 0xfa010000-0xfa0101ff] [ 0.414674] pci 0000:01:00.0: BAR 4: no space for [io size 0x0020] [ 0.414681] pci 0000:01:00.0: BAR 4: failed to assign [io size 0x0020] [ 0.414689] pci 0000:01:00.0: BAR 0: no space for [io size 0x0008] [ 0.414696] pci 0000:01:00.0: BAR 0: failed to assign [io size 0x0008] [ 0.414704] pci 0000:01:00.0: BAR 2: no space for [io size 0x0008] [ 0.414711] pci 0000:01:00.0: BAR 2: failed to assign [io size 0x0008] [ 0.414718] pci 0000:01:00.0: BAR 1: no space for [io size 0x0004] [ 0.414725] pci 0000:01:00.0: BAR 1: failed to assign [io size 0x0004] [ 0.414733] pci 0000:01:00.0: BAR 3: no space for [io size 0x0004] [ 0.414740] pci 0000:01:00.0: BAR 3: failed to assign [io size 0x0004] [ 0.414749] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.414760] pci 0000:00:00.0: bridge window [mem 0xfa000000-0xfa0fffff] [ 0.414815] pcieport 0000:00:00.0: enabling device (0000 -> 0002) [ 0.415041] pcieport 0000:00:00.0: Signaling PME through PCIe PME interrupt [ 0.415048] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 0.415059] pcie_pme 0000:00:00.0:pcie01: service driver pcie_pme loaded [ 0.415161] aer 0000:00:00.0:pcie02: service driver aer loaded [ 0.415806] iep: failed to find iep power down clock source. [ 0.416185] IEP Power ON [ 0.416368] IEP Power OFF [ 0.416396] IEP Driver loaded succesfully [ 0.416548] Module initialized. [ 0.416807] rk-vcodec ff650000.vpu_service: Looking up vcodec-supply from device tree [ 0.416819] rk-vcodec ff650000.vpu_service: Looking up vcodec-supply property in node /vpu_service@ff650000 failed [ 0.416836] rk-vcodec ff650000.vpu_service: no regulator for vcodec [ 0.417060] rk-vcodec ff650000.vpu_service: probe device [ 0.417226] rk-vcodec ff650000.vpu_service: drm allocator with mmu enabled [ 0.417711] rk-vcodec ff650000.vpu_service: could not find power_model node [ 0.417727] rk-vcodec ff650000.vpu_service: init success [ 0.417947] rk-vcodec ff660000.rkvdec: Looking up vcodec-supply from device tree [ 0.417958] rk-vcodec ff660000.rkvdec: Looking up vcodec-supply property in node /rkvdec@ff660000 failed [ 0.417971] rk-vcodec ff660000.rkvdec: no regulator for vcodec [ 0.418373] rk-vcodec ff660000.rkvdec: probe device [ 0.418543] rk-vcodec ff660000.rkvdec: drm allocator with mmu enabled [ 0.418898] rk-vcodec ff660000.rkvdec: could not find power_model node [ 0.418912] rk-vcodec ff660000.rkvdec: init success [ 0.420712] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 0.420723] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12 [ 0.422219] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330 [ 0.422230] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16 [ 0.423288] pwm-regulator vdd-log: GPIO lookup for consumer enable [ 0.423297] pwm-regulator vdd-log: using device tree for GPIO lookup [ 0.423308] of_get_named_gpiod_flags: can't parse 'enable-gpios' property of node '/vdd-log[0]' [ 0.423317] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/vdd-log[0]' [ 0.423325] pwm-regulator vdd-log: using lookup tables for GPIO lookup [ 0.423333] pwm-regulator vdd-log: lookup for GPIO enable failed [ 0.423357] pwm-regulator vdd-log: Looking up pwm-supply from device tree [ 0.423441] pwm-regulator: supplied by vcc_sys [ 0.423450] vcc_sys: could not add device link regulator.8 err -2 [ 0.423528] vdd_log: 800 <--> 1400 mV at 800 mV [ 0.424065] Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled [ 0.425656] ff1a0000.serial: ttyS2 at MMIO 0xff1a0000 (irq = 35, base_baud = 1500000) is a 16550A [ 0.428009] console [ttyS2] enabled [ 0.429022] [drm] Initialized drm 1.1.0 20060810 [ 0.432352] [drm] Rockchip DRM driver version: v1.0.1 [ 0.434123] Unable to detect cache hierarchy for CPU 0 [ 0.434900] brd: module loaded [ 0.439977] loop: module loaded [ 0.440310] lkdtm: No crash points registered, enable through debugfs [ 0.440443] Loading iSCSI transport class v2.0-870. [ 0.440732] iscsi: registered transport (tcp) [ 0.441727] rockchip-spi ff1d0000.spi: no high_speed pinctrl state [ 0.442274] m25p80 spi32766.0: gd25q128 (16384 Kbytes) [ 0.443710] force_sf_dma_mode is ignored if force_thresh_dma_mode is set. [ 0.443726] rk_gmac-dwmac fe300000.ethernet: Looking up phy-supply from device tree [ 0.443817] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input). [ 0.443828] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28). [ 0.443836] rk_gmac-dwmac fe300000.ethernet: RX delay(0x20). [ 0.443860] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no). [ 0.444033] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed [ 0.444681] rk_gmac-dwmac fe300000.ethernet: clock input from PHY [ 0.449695] rk_gmac-dwmac fe300000.ethernet: init for RGMII [ 0.449817] stmmac - user ID: 0x10, Synopsys ID: 0x35 [ 0.449821] Ring mode enabled [ 0.449826] DMA HW capability register supported [ 0.449831] Normal descriptors [ 0.449837] RX Checksum Offload Engine supported (type 2) [ 0.449841] Wake-Up On Lan supported [ 0.449877] Enable RX Mitigation via HW Watchdog Timer [ 0.449979] of_get_named_gpiod_flags: parsed 'snps,reset-gpio' property of node '/ethernet@fe300000[0]' - status (0) [ 0.517881] libphy: stmmac: probed [ 0.517892] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active [ 0.517920] eth%d: PHY ID 001cc916 at 1 IRQ POLL (stmmac-0:01) [ 0.519149] usbcore: registered new interface driver rndis_wlan [ 0.519322] Rockchip WiFi SYS interface (V1.00) ... [ 0.519387] usbcore: registered new interface driver rtl8150 [ 0.519428] usbcore: registered new interface driver r8152 [ 0.519474] usbcore: registered new interface driver asix [ 0.519511] usbcore: registered new interface driver ax88179_178a [ 0.519546] usbcore: registered new interface driver cdc_ether [ 0.519582] usbcore: registered new interface driver rndis_host [ 0.519647] usbcore: registered new interface driver cdc_ncm [ 0.519684] usbcore: registered new interface driver cdc_mbim [ 0.520946] rockchip-dwc3 usb0: failed to get drvdata dwc3 [ 0.525837] rockchip-dwc3 usb1: fail to get drvdata hcd [ 0.527410] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.527426] ehci-pci: EHCI PCI platform driver [ 0.527484] ehci-platform: EHCI generic platform driver [ 0.531266] ehci-platform fe3c0000.usb: EHCI Host Controller [ 0.531430] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 1 [ 0.531610] ehci-platform fe3c0000.usb: irq 29, io mem 0xfe3c0000 [ 0.541256] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00 [ 0.541411] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.541421] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.541430] usb usb1: Product: EHCI Host Controller [ 0.541437] usb usb1: Manufacturer: Linux 4.4.154 ehci_hcd [ 0.541444] usb usb1: SerialNumber: fe3c0000.usb [ 0.541891] hub 1-0:1.0: USB hub found [ 0.541920] hub 1-0:1.0: 1 port detected [ 0.542470] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.542488] ohci-platform: OHCI generic platform driver [ 0.542979] ohci-platform fe3e0000.usb: Generic Platform OHCI controller [ 0.543163] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 2 [ 0.543296] ohci-platform fe3e0000.usb: irq 30, io mem 0xfe3e0000 [ 0.598730] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 0.598739] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.598748] usb usb2: Product: Generic Platform OHCI controller [ 0.598755] usb usb2: Manufacturer: Linux 4.4.154 ohci_hcd [ 0.598762] usb usb2: SerialNumber: fe3e0000.usb [ 0.599180] hub 2-0:1.0: USB hub found [ 0.599211] hub 2-0:1.0: 1 port detected [ 0.600078] usbcore: registered new interface driver cdc_acm [ 0.600084] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 0.600125] usbcore: registered new interface driver cdc_wdm [ 0.600172] usbcore: registered new interface driver uas [ 0.600252] usbcore: registered new interface driver usb-storage [ 0.600327] usbcore: registered new interface driver usbserial [ 0.600359] usbcore: registered new interface driver usbserial_generic [ 0.600387] usbserial: USB Serial support registered for generic [ 0.600427] usbcore: registered new interface driver cp210x [ 0.600453] usbserial: USB Serial support registered for cp210x [ 0.600505] usbcore: registered new interface driver ftdi_sio [ 0.600532] usbserial: USB Serial support registered for FTDI USB Serial Device [ 0.600616] usbcore: registered new interface driver keyspan [ 0.600643] usbserial: USB Serial support registered for Keyspan - (without firmware) [ 0.600669] usbserial: USB Serial support registered for Keyspan 1 port adapter [ 0.600697] usbserial: USB Serial support registered for Keyspan 2 port adapter [ 0.600723] usbserial: USB Serial support registered for Keyspan 4 port adapter [ 0.600762] usbcore: registered new interface driver option [ 0.600788] usbserial: USB Serial support registered for GSM modem (1-port) [ 0.600893] usbcore: registered new interface driver oti6858 [ 0.600919] usbserial: USB Serial support registered for oti6858 [ 0.600956] usbcore: registered new interface driver pl2303 [ 0.600982] usbserial: USB Serial support registered for pl2303 [ 0.601026] usbcore: registered new interface driver qcserial [ 0.601052] usbserial: USB Serial support registered for Qualcomm USB modem [ 0.601097] usbcore: registered new interface driver sierra [ 0.601125] usbserial: USB Serial support registered for Sierra USB modem [ 0.601656] usbcore: registered new interface driver iforce [ 0.601715] usbcore: registered new interface driver xpad [ 0.601832] usbcore: registered new interface driver usbtouchscreen [ 0.602251] i2c /dev entries driver [ 0.603107] fan53555-regulator 0-0040: GPIO lookup for consumer vsel [ 0.603117] fan53555-regulator 0-0040: using device tree for GPIO lookup [ 0.603145] of_get_named_gpiod_flags: parsed 'vsel-gpios' property of node '/i2c@ff3c0000/syr827@40[0]' - status (0) [ 0.603514] fan53555-regulator 0-0040: FAN53555 Option[8] Rev[1] Detected! [ 0.603533] fan53555-regulator 0-0040: Looking up vin-supply from device tree [ 0.603583] fan53555-reg: supplied by vcc_sys [ 0.603593] vcc_sys: could not add device link regulator.9 err -2 [ 0.604924] vdd_cpu_b: 712 <--> 1500 mV at 1000 mV [ 0.605509] fan53555-regulator 0-0041: GPIO lookup for consumer vsel [ 0.605518] fan53555-regulator 0-0041: using device tree for GPIO lookup [ 0.605543] of_get_named_gpiod_flags: parsed 'vsel-gpios' property of node '/i2c@ff3c0000/syr828@41[0]' - status (0) [ 0.605873] fan53555-regulator 0-0041: FAN53555 Option[8] Rev[1] Detected! [ 0.605887] fan53555-regulator 0-0041: Looking up vin-supply from device tree [ 0.605922] fan53555-reg: supplied by vcc_sys [ 0.605930] vcc_sys: could not add device link regulator.10 err -2 [ 0.607482] vdd_gpu: 712 <--> 1500 mV at 1000 mV [ 0.608405] rk808 0-001b: Pmic Chip id: 0x0 [ 0.611433] rk808 0-001b: GPIO lookup for consumer dvs [ 0.611441] rk808 0-001b: using device tree for GPIO lookup [ 0.611452] of_get_named_gpiod_flags: can't parse 'dvs-gpios' property of node '/i2c@ff3c0000/pmic@1b[0]' [ 0.611461] of_get_named_gpiod_flags: can't parse 'dvs-gpio' property of node '/i2c@ff3c0000/pmic@1b[0]' [ 0.611468] rk808 0-001b: using lookup tables for GPIO lookup [ 0.611476] rk808 0-001b: lookup for GPIO dvs failed [ 0.611484] rk808-regulator rk808-regulator: there is no dvs0 gpio [ 0.611491] rk808 0-001b: GPIO lookup for consumer dvs [ 0.611498] rk808 0-001b: using device tree for GPIO lookup [ 0.611506] of_get_named_gpiod_flags: can't parse 'dvs-gpios' property of node '/i2c@ff3c0000/pmic@1b[1]' [ 0.611514] of_get_named_gpiod_flags: can't parse 'dvs-gpio' property of node '/i2c@ff3c0000/pmic@1b[1]' [ 0.611521] rk808 0-001b: using lookup tables for GPIO lookup [ 0.611528] rk808 0-001b: lookup for GPIO dvs failed [ 0.611535] rk808-regulator rk808-regulator: there is no dvs1 gpio [ 0.611576] rk808 0-001b: Looking up vcc1-supply from device tree [ 0.611628] DCDC_REG1: supplied by vcc_sys [ 0.611636] vcc_sys: could not add device link regulator.11 err -2 [ 0.612067] vdd_center: 900 mV [ 0.612321] rk808 0-001b: Looking up vcc2-supply from device tree [ 0.612357] DCDC_REG2: supplied by vcc_sys [ 0.612366] vcc_sys: could not add device link regulator.12 err -2 [ 0.612648] vdd_cpu_l: 750 <--> 1350 mV at 900 mV [ 0.612886] rk808 0-001b: Looking up vcc3-supply from device tree [ 0.612921] DCDC_REG3: supplied by vcc_sys [ 0.612932] vcc_sys: could not add device link regulator.13 err -2 [ 0.612961] vcc_ddr: at 5000 mV [ 0.613163] rk808 0-001b: Looking up vcc4-supply from device tree [ 0.613198] DCDC_REG4: supplied by vcc_sys [ 0.613206] vcc_sys: could not add device link regulator.14 err -2 [ 0.613389] vcc_1v8: 1800 mV [ 0.613614] rk808 0-001b: Looking up vcc6-supply from device tree [ 0.613649] LDO_REG1: supplied by vcc_sys [ 0.613656] vcc_sys: could not add device link regulator.15 err -2 [ 0.614601] vcc1v8_dvp: 1800 mV [ 0.614832] rk808 0-001b: Looking up vcc6-supply from device tree [ 0.614867] LDO_REG2: supplied by vcc_sys [ 0.614875] vcc_sys: could not add device link regulator.16 err -2 [ 0.615047] vcc3v0_touch: Bringing 1800000uV into 3000000-3000000uV [ 0.615166] vcc3v0_touch: ramp_delay not set [ 0.615801] vcc3v0_touch: 3000 mV [ 0.616040] rk808 0-001b: Looking up vcc7-supply from device tree [ 0.616075] LDO_REG3: supplied by vcc_sys [ 0.616083] vcc_sys: could not add device link regulator.17 err -2 [ 0.616773] vcc1v8_pmu: 1800 mV [ 0.617016] rk808 0-001b: Looking up vcc9-supply from device tree [ 0.617051] LDO_REG4: supplied by vcc_sys [ 0.617059] vcc_sys: could not add device link regulator.18 err -2 [ 0.617746] vcc_sd: 1800 <--> 3300 mV at 3000 mV [ 0.618013] rk808 0-001b: Looking up vcc9-supply from device tree [ 0.618049] LDO_REG5: supplied by vcc_sys [ 0.618057] vcc_sys: could not add device link regulator.19 err -2 [ 0.618226] vcca3v0_codec: Bringing 1800000uV into 3000000-3000000uV [ 0.618345] vcca3v0_codec: ramp_delay not set [ 0.618979] vcca3v0_codec: 3000 mV [ 0.619217] rk808 0-001b: Looking up vcc10-supply from device tree [ 0.619251] LDO_REG6: supplied by vcc_sys [ 0.619259] vcc_sys: could not add device link regulator.20 err -2 [ 0.619956] vcc_1v5: 1500 mV [ 0.620194] rk808 0-001b: Looking up vcc7-supply from device tree [ 0.620228] LDO_REG7: supplied by vcc_sys [ 0.620236] vcc_sys: could not add device link regulator.21 err -2 [ 0.620414] vcca1v8_codec: Bringing 800000uV into 1800000-1800000uV [ 0.620533] vcca1v8_codec: ramp_delay not set [ 0.621166] vcca1v8_codec: 1800 mV [ 0.621423] rk808 0-001b: Looking up vcc11-supply from device tree [ 0.621459] LDO_REG8: supplied by vcc_sys [ 0.621467] vcc_sys: could not add device link regulator.22 err -2 [ 0.622154] vcc_3v0: 3000 mV [ 0.622406] rk808 0-001b: Looking up vcc8-supply from device tree [ 0.622444] SWITCH_REG1: supplied by vcc3v3_sys [ 0.622452] vcc3v3_sys: could not add device link regulator.23 err -2 [ 0.622482] vcc3v3_s3: at 3300 mV [ 0.622713] rk808 0-001b: Looking up vcc12-supply from device tree [ 0.622748] SWITCH_REG2: supplied by vcc3v3_sys [ 0.622756] vcc3v3_sys: could not add device link regulator.24 err -2 [ 0.622784] vcc3v3_s0: at 3300 mV [ 0.626049] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0 [ 0.626475] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff80093f6000 [ 0.627101] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff80093f8000 [ 0.627827] fusb302 4-0022: GPIO lookup for consumer int-n [ 0.627837] fusb302 4-0022: using device tree for GPIO lookup [ 0.627867] of_get_named_gpiod_flags: parsed 'int-n-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' - status (0) [ 0.627920] fusb302 4-0022: GPIO lookup for consumer vbus-5v [ 0.627929] fusb302 4-0022: using device tree for GPIO lookup [ 0.627954] of_get_named_gpiod_flags: parsed 'vbus-5v-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' - status (0) [ 0.627979] fusb302 4-0022: GPIO lookup for consumer vbus-other [ 0.627986] fusb302 4-0022: using device tree for GPIO lookup [ 0.627995] of_get_named_gpiod_flags: can't parse 'vbus-other-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' [ 0.628003] of_get_named_gpiod_flags: can't parse 'vbus-other-gpio' property of node '/i2c@ff3d0000/fusb30x@22[0]' [ 0.628011] fusb302 4-0022: using lookup tables for GPIO lookup [ 0.628019] fusb302 4-0022: lookup for GPIO vbus-other failed [ 0.628027] fusb302 4-0022: GPIO lookup for consumer discharge [ 0.628033] fusb302 4-0022: using device tree for GPIO lookup [ 0.628041] of_get_named_gpiod_flags: can't parse 'discharge-gpios' property of node '/i2c@ff3d0000/fusb30x@22[0]' [ 0.628049] of_get_named_gpiod_flags: can't parse 'discharge-gpio' property of node '/i2c@ff3d0000/fusb30x@22[0]' [ 0.628056] fusb302 4-0022: using lookup tables for GPIO lookup [ 0.628063] fusb302 4-0022: lookup for GPIO discharge failed [ 0.628212] fusb302 4-0022: Can't get property of role, set role to default DRP [ 0.636395] fusb302 4-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE [ 0.636420] rk3x-i2c ff3d0000.i2c: Initialized RK3xxx I2C bus at ffffff80093fa000 [ 0.637368] rockchip-iodomain ff320000.syscon:io-domains: Looking up pmu1830-supply from device tree [ 0.637588] rockchip-iodomain ff770000.syscon:io-domains: Looking up bt656-supply from device tree [ 0.637691] rockchip-iodomain ff770000.syscon:io-domains: Looking up audio-supply from device tree [ 0.637758] rockchip-iodomain ff770000.syscon:io-domains: Looking up sdmmc-supply from device tree [ 0.637810] rockchip-iodomain ff770000.syscon:io-domains: Looking up gpio1830-supply from device tree [ 0.639459] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647 [ 0.640379] rockchip-thermal ff260000.tsadc: tsadc is probed successfully! [ 0.641088] Bluetooth: Virtual HCI driver ver 1.5 [ 0.641195] Bluetooth: HCI UART driver ver 2.3 [ 0.641204] Bluetooth: HCI UART protocol H4 registered [ 0.641211] Bluetooth: HCI UART protocol Three-wire (H5) registered [ 0.641381] usbcore: registered new interface driver bfusb [ 0.641439] usbcore: registered new interface driver btusb [ 0.641451] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 0.642016] cpu cpu0: leakage=18 [ 0.642044] cpu cpu0: Looking up cpu-supply from device tree [ 0.653964] cpu cpu0: temp=30000, pvtm=141433 (142698 + -1265) [ 0.654149] cpu cpu0: pvtm-volt-sel=0 [ 0.654481] cpu cpu4: leakage=35 [ 0.654504] cpu cpu4: Looking up cpu-supply from device tree [ 0.666545] cpu cpu4: temp=30000, pvtm=148946 (149727 + -781) [ 0.666624] cpu cpu4: pvtm-volt-sel=0 [ 0.666898] cpu cpu0: Looking up cpu-supply from device tree [ 0.667140] cpu cpu0: Looking up cpu-supply from device tree [ 0.667778] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 [ 0.668554] cpu cpu4: Looking up cpu-supply from device tree [ 0.669188] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 [ 0.672324] sdhci: Secure Digital Host Controller Interface driver [ 0.672329] sdhci: Copyright(c) Pierre Ossman [ 0.672334] Synopsys Designware Multimedia Card Interface Driver [ 0.672726] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode. [ 0.672794] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller. [ 0.672804] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a [ 0.672833] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo [ 0.672855] dwmmc_rockchip fe320000.dwmmc: Looking up vmmc-supply from device tree [ 0.672860] dwmmc_rockchip fe320000.dwmmc: Looking up vmmc-supply property in node /dwmmc@fe320000 failed [ 0.672884] dwmmc_rockchip fe320000.dwmmc: Looking up vqmmc-supply from device tree [ 0.672931] dwmmc_rockchip fe320000.dwmmc: No vmmc regulator found [ 0.672944] dwmmc_rockchip fe320000.dwmmc: GPIO lookup for consumer cd [ 0.672947] dwmmc_rockchip fe320000.dwmmc: using device tree for GPIO lookup [ 0.672953] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/dwmmc@fe320000[0]' [ 0.672957] of_get_named_gpiod_flags: can't parse 'cd-gpio' property of node '/dwmmc@fe320000[0]' [ 0.672961] dwmmc_rockchip fe320000.dwmmc: using lookup tables for GPIO lookup [ 0.672965] dwmmc_rockchip fe320000.dwmmc: lookup for GPIO cd failed [ 0.672969] dwmmc_rockchip fe320000.dwmmc: GPIO lookup for consumer wp [ 0.672972] dwmmc_rockchip fe320000.dwmmc: using device tree for GPIO lookup [ 0.672976] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/dwmmc@fe320000[0]' [ 0.672980] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/dwmmc@fe320000[0]' [ 0.672983] dwmmc_rockchip fe320000.dwmmc: using lookup tables for GPIO lookup [ 0.672986] dwmmc_rockchip fe320000.dwmmc: lookup for GPIO wp failed [ 0.673077] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done [ 0.673205] vcc_sd: ramp_delay not set [ 0.673210] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done [ 0.684666] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0) [ 0.699036] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized [ 0.699243] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.702101] sdhci-arasan fe330000.sdhci: GPIO lookup for consumer wp [ 0.702156] sdhci-arasan fe330000.sdhci: using device tree for GPIO lookup [ 0.702182] of_get_named_gpiod_flags: can't parse 'wp-gpios' property of node '/sdhci@fe330000[0]' [ 0.702205] of_get_named_gpiod_flags: can't parse 'wp-gpio' property of node '/sdhci@fe330000[0]' [ 0.702225] sdhci-arasan fe330000.sdhci: using lookup tables for GPIO lookup [ 0.702247] sdhci-arasan fe330000.sdhci: lookup for GPIO wp failed [ 0.703558] sdhci-arasan fe330000.sdhci: Looking up vmmc-supply from device tree [ 0.703587] sdhci-arasan fe330000.sdhci: Looking up vmmc-supply property in node /sdhci@fe330000 failed [ 0.703662] sdhci-arasan fe330000.sdhci: Looking up vqmmc-supply from device tree [ 0.703688] sdhci-arasan fe330000.sdhci: Looking up vqmmc-supply property in node /sdhci@fe330000 failed [ 0.703757] sdhci-arasan fe330000.sdhci: No vmmc regulator found [ 0.703777] sdhci-arasan fe330000.sdhci: No vqmmc regulator found [ 0.728684] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0) [ 0.729154] mmc0: new high speed SDHC card at address 59b4 [ 0.729831] mmcblk0: mmc0:59b4 ND4GB 3.73 GiB [ 0.730767] mmcblk0: p1 p2 [ 0.731477] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA [ 0.731958] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/work-led[0]' - status (0) [ 0.732063] of_get_named_gpiod_flags: parsed 'gpios' property of node '/leds/diy-led[0]' - status (0) [ 0.732171] ledtrig-cpu: registered to indicate activity on CPUs [ 0.732210] hidraw: raw HID events driver (C) Jiri Kosina [ 0.734877] usbcore: registered new interface driver usbhid [ 0.734880] usbhid: USB HID core driver [ 0.735319] rockchip-dmc dmc: unable to get devfreq-event device : dfi [ 0.738172] rockchip-saradc ff100000.saradc: Looking up vref-supply from device tree [ 0.738178] rockchip-saradc ff100000.saradc: Looking up vref-supply property in node /saradc@ff100000 failed [ 0.738199] ff100000.saradc supply vref not found, using dummy regulator [ 0.739848] of_get_named_gpiod_flags: can't parse 'spk-con-gpio' property of node '/i2c@ff110000/es8316@10[0]' [ 0.739856] es8316 1-0010: Can not read property spk_ctl_gpio [ 0.739871] of_get_named_gpiod_flags: parsed 'hp-det-gpio' property of node '/i2c@ff110000/es8316@10[0]' - status (0) [ 0.742605] NET: Registered protocol family 10 [ 0.743293] NET: Registered protocol family 17 [ 0.743501] Bluetooth: RFCOMM socket layer initialized [ 0.743515] Bluetooth: RFCOMM ver 1.11 [ 0.743524] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 0.743529] Bluetooth: HIDP socket layer initialized [ 0.743655] [WLAN_RFKILL]: Enter rfkill_wlan_init [ 0.743764] [BT_RFKILL]: Enter rfkill_rk_init [ 0.743855] Key type dns_resolver registered [ 0.747026] phy phy-ff770000.syscon:usb2-phy@e450.6: Looking up phy-supply from device tree [ 0.747098] vcc5v0_host: could not add device link phy-ff770000.syscon:usb2-phy@e450.6 err -2 [ 0.747513] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up phy-supply from device tree [ 0.747519] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up phy-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed [ 0.747886] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up vbus-supply from device tree [ 0.747891] phy phy-ff770000.syscon:usb2-phy@e450.7: Looking up vbus-supply property in node /syscon@ff770000/usb2-phy@e450/otg-port failed [ 0.747922] phy phy-ff770000.syscon:usb2-phy@e450.7: Failed to get VBUS supply regulator [ 0.748702] phy phy-ff7c0000.phy.8: Looking up phy-supply from device tree [ 0.748709] phy phy-ff7c0000.phy.8: Looking up phy-supply property in node /phy@ff7c0000/dp-port failed [ 0.748770] phy phy-ff7c0000.phy.9: Looking up phy-supply from device tree [ 0.748774] phy phy-ff7c0000.phy.9: Looking up phy-supply property in node /phy@ff7c0000/usb3-port failed [ 0.749088] rockchip-drm display-subsystem: defer getting devfreq [ 0.749400] rockchip-drm display-subsystem: bound ff900000.vop (ops 0xffffff8008a1edb0) [ 0.749664] i2c i2c-9: of_i2c: modalias failure on /hdmi@ff940000/ports [ 0.750261] dwhdmi-rockchip ff940000.hdmi: registered DesignWare HDMI I2C bus driver [ 0.750316] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY) [ 0.753127] rockchip-drm display-subsystem: bound ff940000.hdmi (ops 0xffffff8008a13838) [ 0.754370] i2c i2c-10: of_i2c: modalias failure on /dp@fec00000/ports [ 0.755684] rockchip-drm display-subsystem: bound fec00000.dp (ops 0xffffff8008a14810) [ 0.755706] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 0.755719] [drm] No driver support for vblank timestamp query. [ 0.755961] rockchip-drm display-subsystem: failed to parse loader memory [ 0.756012] rockchip-drm display-subsystem: No connectors reported connected with modes [ 0.756036] [drm] Cannot find any crtc or sizes - going 1024x768 [ 0.763678] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2 [ 0.766634] Console: switching to colour frame buffer device 128x48 [ 0.769447] rockchip-drm display-subsystem: fb0: frame buffer device [ 0.774240] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller [ 0.774403] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 3 [ 0.774605] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010 [ 0.774633] xhci-hcd xhci-hcd.9.auto: irq 228, io mem 0xfe800000 [ 0.774713] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.774718] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.774722] usb usb3: Product: xHCI Host Controller [ 0.774725] usb usb3: Manufacturer: Linux 4.4.154 xhci-hcd [ 0.774729] usb usb3: SerialNumber: xhci-hcd.9.auto [ 0.774974] hub 3-0:1.0: USB hub found [ 0.774989] hub 3-0:1.0: 1 port detected [ 0.775134] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller [ 0.775200] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 4 [ 0.775229] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 0.775270] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 0.775274] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.775278] usb usb4: Product: xHCI Host Controller [ 0.775281] usb usb4: Manufacturer: Linux 4.4.154 xhci-hcd [ 0.775284] usb usb4: SerialNumber: xhci-hcd.9.auto [ 0.775489] hub 4-0:1.0: USB hub found [ 0.775504] hub 4-0:1.0: 1 port detected [ 0.776260] xhci-hcd xhci-hcd.9.auto: remove, state 1 [ 0.776271] usb usb4: USB disconnect, device number 1 [ 0.795164] xhci-hcd xhci-hcd.9.auto: Host not halted after 16000 microseconds. [ 0.795169] xhci-hcd xhci-hcd.9.auto: Host controller not halted, aborting reset. [ 0.795190] xhci-hcd xhci-hcd.9.auto: USB bus 4 deregistered [ 0.795269] xhci-hcd xhci-hcd.9.auto: remove, state 1 [ 0.795278] usb usb3: USB disconnect, device number 1 [ 0.795621] xhci-hcd xhci-hcd.9.auto: USB bus 3 deregistered [ 0.799754] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller [ 0.799901] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus number 3 [ 0.800065] xhci-hcd xhci-hcd.10.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x02030010 [ 0.800092] xhci-hcd xhci-hcd.10.auto: irq 229, io mem 0xfe900000 [ 0.800173] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.800177] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.800181] usb usb3: Product: xHCI Host Controller [ 0.800185] usb usb3: Manufacturer: Linux 4.4.154 xhci-hcd [ 0.800188] usb usb3: SerialNumber: xhci-hcd.10.auto [ 0.800422] hub 3-0:1.0: USB hub found [ 0.800436] hub 3-0:1.0: 1 port detected [ 0.800575] xhci-hcd xhci-hcd.10.auto: xHCI Host Controller [ 0.800652] xhci-hcd xhci-hcd.10.auto: new USB bus registered, assigned bus number 4 [ 0.800680] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 0.800726] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003 [ 0.800730] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.800733] usb usb4: Product: xHCI Host Controller [ 0.800736] usb usb4: Manufacturer: Linux 4.4.154 xhci-hcd [ 0.800740] usb usb4: SerialNumber: xhci-hcd.10.auto [ 0.800942] hub 4-0:1.0: USB hub found [ 0.800956] hub 4-0:1.0: 1 port detected [ 0.804589] ehci-platform fe380000.usb: EHCI Host Controller [ 0.806684] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 5 [ 0.806817] ehci-platform fe380000.usb: irq 27, io mem 0xfe380000 [ 0.814619] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00 [ 0.814703] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002 [ 0.814708] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.814712] usb usb5: Product: EHCI Host Controller [ 0.814716] usb usb5: Manufacturer: Linux 4.4.154 ehci_hcd [ 0.814719] usb usb5: SerialNumber: fe380000.usb [ 0.815382] hub 5-0:1.0: USB hub found [ 0.815399] hub 5-0:1.0: 1 port detected [ 0.815863] ohci-platform fe3a0000.usb: Generic Platform OHCI controller [ 0.816063] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 6 [ 0.816176] ohci-platform fe3a0000.usb: irq 28, io mem 0xfe3a0000 [ 0.872183] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 0.872192] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.872197] usb usb6: Product: Generic Platform OHCI controller [ 0.872200] usb usb6: Manufacturer: Linux 4.4.154 ohci_hcd [ 0.872204] usb usb6: SerialNumber: fe3a0000.usb [ 0.872660] hub 6-0:1.0: USB hub found [ 0.872677] hub 6-0:1.0: 1 port detected [ 0.873123] pwrseq_simple sdio-pwrseq: GPIO lookup for consumer reset [ 0.873127] pwrseq_simple sdio-pwrseq: using device tree for GPIO lookup [ 0.873141] of_get_named_gpiod_flags: parsed 'reset-gpios' property of node '/sdio-pwrseq[0]' - status (0) [ 0.873282] rockchip-dmc dmc: Looking up center-supply from device tree [ 0.873411] rockchip-dmc dmc: Failed to get leakage [ 0.873887] rockchip-dmc dmc: Looking up center-supply from device tree [ 0.873899] vdd_center: could not add device link dmc err -17 [ 0.873905] vdd_center: Failed to create debugfs directory [ 0.873909] rockchip-dmc dmc: Failed to get pvtm [ 0.874460] rockchip-dmc dmc: failed to get vop bandwidth to dmc rate [ 0.875197] rockchip-dmc dmc: could not find power_model node [ 0.875941] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/hdmi-sound[0]' [ 0.875945] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/hdmi-sound[0]' [ 0.876542] asoc-simple-card hdmi-sound: i2s-hifi <-> ff8a0000.i2s mapping ok [ 0.878180] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/es8316-sound[0]' [ 0.878188] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/es8316-sound[0]' [ 1.006808] asoc-simple-card es8316-sound: ES8316 HiFi <-> ff890000.i2s mapping ok [ 1.006828] asoc-simple-card es8316-sound: ASoC: no source widget found for MICBIAS1 [ 1.007563] asoc-simple-card es8316-sound: ASoC: Failed to add route MICBIAS1 -> direct -> Mic Jack [ 1.008426] asoc-simple-card es8316-sound: ASoC: no sink widget found for IN1P [ 1.009098] asoc-simple-card es8316-sound: ASoC: Failed to add route Mic Jack -> direct -> IN1P [ 1.011133] es8316 1-0010: ASoC: Failed to create Left Hp mixer debugfs file [ 1.011139] es8316 1-0010: ASoC: Failed to create Right Hp mixer debugfs file [ 1.011309] es8316 1-0010: ASoC: Failed to create HPCP L debugfs file [ 1.011475] es8316 1-0010: ASoC: Failed to create HPCP R debugfs file [ 1.011643] es8316 1-0010: ASoC: Failed to create HPVOL L debugfs file [ 1.011809] es8316 1-0010: ASoC: Failed to create HPVOL R debugfs file [ 1.013165] of_get_named_gpiod_flags: can't parse 'simple-audio-card,hp-det-gpio' property of node '/spdif-sound[0]' [ 1.013171] of_get_named_gpiod_flags: can't parse 'simple-audio-card,mic-det-gpio' property of node '/spdif-sound[0]' [ 1.013273] rockchip-spdif ff870000.spdif: Missing dma channel for stream: 0 [ 1.013937] rockchip-spdif ff870000.spdif: ASoC: pcm constructor failed: -22 [ 1.014613] asoc-simple-card spdif-sound: ASoC: can't create pcm ff870000.spdif-dit-hifi :-22 [ 1.015404] asoc-simple-card spdif-sound: ASoC: failed to instantiate card -22 [ 1.016151] asoc-simple-card: probe of spdif-sound failed with error -22 [ 1.016281] console [netcon0] enabled [ 1.016285] netconsole: network logging started [ 1.017195] rk808-rtc rk808-rtc: setting system clock to 2013-01-18 08:50:06 UTC (1358499006) [ 1.027558] ALSA device list: [ 1.027567] #0: HDMI [ 1.027569] #1: ES8316 [ 1.029220] Freeing unused kernel memory: 2880K [ 1.086269] Checking disk(s): UUID=2211-5513 UUID=a321c910-4860-4321-bec0-31d20884f00c [ 1.579168] fsck: CP437: Invalid argument [ 1.579345] fsck: fsck.fat 4.1 (2017-01-24) [ 1.579572] fsck: /dev/mmcblk0p1: 8 files, 19198/65501 clusters [ 1.579822] fsck: STORAGE: Superblock last mount time is in the future. [ 1.580150] fsck: (by less than a day, probably due to the hardware clock being incorrectly set) [ 1.580398] fsck: STORAGE: Superblock last write time is in the future. [ 1.580722] fsck: (by less than a day, probably due to the hardware clock being incorrectly set) [ 1.580979] fsck: STORAGE: clean, 2612/843776 files, 184328/3374080 blocks [ 1.764790] cdn-dp fec00000.dp: Direct firmware load for rockchip/dptx.bin failed with error -2 [ 1.811517] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities [ 1.812093] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities [ 1.867849] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.307402] systemd[1]: System time before build time, advancing clock. [ 2.309490] cgroup: cgroup2: unknown option "nsdelegate" [ 2.315699] systemd[1]: systemd 242 running in system mode. (-PAM -AUDIT -SELINUX -IMA -APPARMOR -SMACK +SYSVINIT -UTMP -LIBCRYPTSETUP -GCRYPT -GNUTLS -ACL -XZ -LZ4 -SECCOMP +BLKID -ELFUTILS +KMOD +IDN2 -IDN -PCRE2 default-hierarchy=hybrid) [ 2.316476] systemd[1]: Detected architecture arm64. [ 2.318753] systemd[1]: Set hostname to . [ 2.388667] systemd[1]: File /usr/lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling. [ 2.388684] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.) [ 2.486905] random: systemd: uninitialized urandom read (16 bytes read, 58 bits of entropy available) [ 2.487386] systemd[1]: Listening on Journal Socket. [ 2.487650] random: systemd: uninitialized urandom read (16 bytes read, 58 bits of entropy available) [ 2.491493] systemd[1]: Mounting Variable Directory... [ 2.492144] systemd[1]: Condition check resulted in Huge Pages File System being skipped. [ 2.492288] random: systemd: uninitialized urandom read (16 bytes read, 58 bits of entropy available) [ 2.492771] systemd[1]: Listening on udev Control Socket. [ 2.493083] random: systemd: uninitialized urandom read (16 bytes read, 58 bits of entropy available) [ 2.496051] systemd[1]: Mounting Kernel Debug File System... [ 2.496492] random: systemd: uninitialized urandom read (16 bytes read, 58 bits of entropy available) [ 2.499737] systemd[1]: Starting Show Version... [ 2.499841] random: systemd: uninitialized urandom read (16 bytes read, 58 bits of entropy available) [ 2.501288] systemd[1]: Created slice User and Session Slice. [ 2.501382] random: systemd: uninitialized urandom read (16 bytes read, 59 bits of entropy available) [ 2.501425] systemd[1]: Reached target Slices. [ 2.501500] random: systemd: uninitialized urandom read (16 bytes read, 59 bits of entropy available) [ 2.501919] systemd[1]: Listening on Journal Socket (/dev/log). [ 2.502035] random: systemd: uninitialized urandom read (16 bytes read, 59 bits of entropy available) [ 2.502238] systemd[1]: Started Forward Password Requests to Wall Directory Watch. [ 2.570798] systemd[1]: Condition check resulted in Journal Audit Socket being skipped. [ 2.572688] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped. [ 2.573052] random: systemd: uninitialized urandom read (16 bytes read, 60 bits of entropy available) [ 2.575556] systemd[1]: Mounting POSIX Message Queue File System... [ 2.578743] systemd[1]: Starting Setup NTP servers for timesyncd... [ 2.580075] systemd[1]: Listening on RPCbind Server Activation Socket. [ 2.580207] systemd[1]: Reached target RPC Port Mapper. [ 2.580533] systemd[1]: Started Dispatch Password Requests to Console Directory Watch. [ 2.580932] systemd[1]: Listening on udev Kernel Socket. [ 2.581078] systemd[1]: Reached target Paths. [ 2.584761] systemd[1]: Starting Create Persistent Log Directory on /storage... [ 2.585276] systemd[1]: Listening on initctl Compatibility Named Pipe. [ 2.592338] systemd[1]: Mounted Variable Directory. [ 2.592789] systemd[1]: Mounted Kernel Debug File System. [ 2.594322] systemd[1]: Started Show Version. [ 2.596868] systemd[1]: Mounted POSIX Message Queue File System. [ 2.601812] systemd[1]: Starting Create kernel modules tree from overlays... [ 2.603127] systemd[1]: Started Setup NTP servers for timesyncd. [ 2.604427] systemd[1]: Started Create Persistent Log Directory on /storage. [ 2.605235] systemd[1]: Condition check resulted in Persistent Log Storage being skipped. [ 2.633357] kernel-overlays-setup: setup base modules [ 2.666853] kernel-overlays-setup: added modules from /usr/lib/kernel-overlays/base/lib/modules/4.4.154 [ 2.698994] kernel-overlays-setup: added firmware from /usr/lib/kernel-overlays/base/lib/firmware [ 2.699135] kernel-overlays-setup: adding overlays from /storage/.cache/kernel-overlays [ 2.700462] kernel-overlays-setup: done [ 2.701310] systemd[1]: kernel-overlays.service: Succeeded. [ 2.702098] systemd[1]: Started Create kernel modules tree from overlays. [ 2.704500] systemd[1]: Starting udev Coldplug all Devices... [ 2.707475] systemd[1]: Starting Setup machine-id... [ 2.710214] systemd[1]: Starting Mounting swapfile... [ 2.714083] systemd[1]: Starting Create list of required static device nodes for the current kernel... [ 2.727411] systemd[1]: Starting Load Kernel Modules... [ 2.759100] systemd[1]: Started Create list of required static device nodes for the current kernel. [ 2.761687] systemd[1]: Started Setup machine-id. [ 2.766196] systemd[1]: Starting Journal Service... [ 2.770432] systemd[1]: Starting Create Static Device Nodes in /dev... [ 2.833480] wireguard: loading out-of-tree module taints kernel. [ 2.835227] wireguard: WireGuard 0.0.20200215 loaded. See www.wireguard.com for information. [ 2.835236] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved. [ 2.837279] systemd[1]: Started Load Kernel Modules. [ 2.840594] systemd[1]: Mounting Kernel Configuration File System... [ 2.841056] systemd[1]: Condition check resulted in FUSE Control File System being skipped. [ 2.844154] systemd[1]: Starting Apply Kernel Variables... [ 2.854530] systemd[1]: Started Create Static Device Nodes in /dev. [ 2.857281] systemd[1]: Mounted Kernel Configuration File System. [ 2.865457] systemd[1]: Started Apply Kernel Variables. [ 2.902475] systemd[1]: Started Mounting swapfile. [ 2.902871] systemd[1]: Reached target Swap. [ 2.905273] systemd[1]: Mounting Temporary Directory (/tmp)... [ 2.911520] systemd[1]: Mounted Temporary Directory (/tmp). [ 2.911980] systemd[1]: Reached target Local File Systems. [ 2.966482] systemd[1]: Started udev Coldplug all Devices. [ 2.989946] systemd[1]: Started Journal Service. [ 3.011555] systemd-journald[250]: Received request to flush runtime journal from PID 1 [ 3.515412] random: nonblocking pool is initialized [ 3.761288] vendor storage:20160801 ret = -1 [ 3.792492] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Not connected. Disabling cdn [ 4.132028] mali ff9a0000.gpu: Looking up mali-supply from device tree [ 4.132185] mali ff9a0000.gpu: leakage=23 [ 4.132200] mali ff9a0000.gpu: Looking up mali-supply from device tree [ 4.132214] vdd_gpu: could not add device link ff9a0000.gpu err -17 [ 4.132220] vdd_gpu: Failed to create debugfs directory [ 4.144476] mali ff9a0000.gpu: temp=28750, pvtm=119190 (119788 + -598) [ 4.145271] mali ff9a0000.gpu: pvtm-volt-sel=0 [ 4.146162] mali ff9a0000.gpu: GPU identified as 0x0860 r2p0 status 0 [ 4.146482] mali ff9a0000.gpu: Protected mode not available [ 4.147637] mali ff9a0000.gpu: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 [ 4.147676] mali ff9a0000.gpu: Using configured power model mali-simple-power-model, and fallback mali-simple-power-model [ 4.147760] I : [File] : drivers/gpu/arm/midgard/backend/gpu/mali_kbase_devfreq.c; [Line] : 413; [Func] : kbase_devfreq_init(); success initing power_model_simple. [ 4.148260] mali ff9a0000.gpu: Probed as mali0 [ 4.210025] of_get_named_gpiod_flags: parsed 'gpios' property of node '/ir-receiver[0]' - status (0) [ 4.277918] Registered IR keymap rc-pine64 [ 4.278127] input: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc0/input0 [ 4.278643] rc0: gpio_ir_recv as /devices/platform/ir-receiver/rc/rc0 [ 4.283666] IR RC5(x/sz) protocol handler initialized [ 4.284292] IR NEC protocol handler initialized [ 4.286270] IR Sony protocol handler initialized [ 4.286711] IR RC6 protocol handler initialized [ 4.288186] IR JVC protocol handler initialized [ 4.290091] IR Sharp protocol handler initialized [ 4.291942] IR SANYO protocol handler initialized [ 4.295266] IR MCE Keyboard/mouse protocol handler initialized [ 4.295478] IR XMP protocol handler initialized [ 4.296557] input: MCE IR Keyboard/Mouse (gpio-rc-recv) as /devices/virtual/input/input1 [ 4.301016] lirc_dev: IR Remote Control driver registered, major 242 [ 4.307974] rc rc0: lirc_dev: driver ir-lirc-codec (gpio-rc-recv) registered at minor = 0 [ 4.307983] IR LIRC bridge handler initialized [ 6.604954] rk_gmac-dwmac fe300000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 7.754499] dwhdmi-rockchip ff940000.hdmi: Rate 0 missing; compute N dynamically [ 8.333571] dwhdmi-rockchip ff940000.hdmi: Rate 0 missing; compute N dynamically