bumerc@bumerc-linux-server:~$ sudo kermit [sudo] Passwort für bumerc: Connecting to /dev/ttyUSB0, speed 115200 Escape character: Ctrl-\ (ASCII 28, FS): enabled Type the escape character followed by C to get back, or followed by ? to see other options. ---------------------------------------------------- GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0; TE: 51437 BL2 Built : 18:50:13, Sep 22 2017. gxl g4786fda-dirty - jiaxing.ye@droid12 set vdd cpu_a to 1120 mv set vdd cpu_b to 1050 mv set vddee to 1000 mv Board ID = 1 CPU clk: 1200MHz DQS-corr enabled DDR scramble disabled STICKY_REG0: 0x00000000 STICKY_REG8: 0x00000000 STICKY_REG9: 0x00000000 LPDDR3 chl: Rank0+1 @ 792MHz ddr_lpddr3_only_up_odt_enable: 0x00000001.... Training PGSR0: 0x80001fbf.... ddr_training_inf: rank: 0 org_wr0 w0_l w0_r org_r0 r0_l r0_r org_wr1 w1_l w1_r org_r1 r1_l r1_r org_wr2 w2_l w2_r org_r2 r2_l r2_r org_wr3 w3_l w3_r org_r3 r3_l r3_r af_vrefddr_training_win: rank: 0 19 00 36 33 16 52 16 00 2c 3f 1f 5f 1b 00 37 33 13 53 19 00 33 34 15 54 742 rank: 1 1a 00 36 34 16 52 15 00 2c 3f 1f 5f 1b 00 37 33 13 53 19 00 33 34 15 54 742 bist_test rank: 0 1b 10 27 36 29 43 11 00 22 3b 2e 49 1f 10 2f 34 24 45 1c 0a 2f 31 21 42 742 rank: 1 1b 10 26 34 28 41 10 00 20 3c 2e 4a 1f 10 2e 32 23 42 1b 09 2e 31 21 42 742 bist_size0x 000007e0 bist_cost_time 253274 us bist test no threshold setting: ddr_refi_counter37 DDR1_ADDRMAP_0== 0x14941cc5 DDR1_ADDRMAP_1== 0x230783ab DDR1_ADDRMAP_2== 0x2f6ad272 DDR1_ADDRMAP_3== 0x3bcdeb38 DDR1_ADDRMAP_4== 0x0007359e Rank0: 2048MB-2T-3 Rank1: 1024MB-2T-3 DataBus test pass! AddrBus test pass! -s Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000 New fip structure! Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600 Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x00018400 Load bl33 from eMMC, src: 0x0003c200, des: 0x01000000, size: 0x00074000 NOTICE: BL3-1: v1.0(release):3348978 NOTICE: BL3-1: Built : 15:44:01, May 12 2017 NOTICE: BL3-1: BL33 decompress pass mpu_config_enable:ok [Image: gxl_v1.1.3221-2cfba69 2017-05-27 16:03:58 qiufang.dai@droid07] OPS=0x82 wdt: reset registers! b4 4b 34 87 31 36 df 54 9d 41 1f 65 [0.597785 Inits done] secure task start! high task start! low task start! ERROR: Error initializing runtime service opteed_fast U-Boot 2015.01-g5e3f75b-dirty (Oct 10 2017 - 18:20:38) DRAM: 3 GiB Relocation Offset is: b6e98000 register usb cfg[0][1] = 00000000b7f5aeb0 [CANVAS]canvas init vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters vpu: clk_level = 7 vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300) vpu: vpu_clk_gate_init_off vpp: vpp_init boot_device_flag : 1 Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc. init bus_cycle=6, bus_timing=7, system=5.0ns reset failed get_chip_type and ret:fffffffe get_chip_type and ret:fffffffe chip detect failed and ret:fffffffe nandphy_init failed and ret=0xfffffff1 MMC: aml_priv->desc_buf = 0x00000000b3e986b0 aml_priv->desc_buf = 0x00000000b3e9a9d0 SDIO Port B: 0, SDIO Port C: 1 emmc/sd response timeout, cmd8, status=0x1ff2800 emmc/sd response timeout, cmd55, status=0x1ff2800 init_part() 293: PART_TYPE_AML [mmc_init] mmc init success dtb magic 5f4c4d41 Amlogic multi-dtb tool Multi dtb detected edwin--->DDR size: 0xb8000000 Multi dtb tool version: v2 . Support 2 dtbs. aml_dt soc: gxm platform: q201 variant: 3g dtb 0 soc: gxm plat: q201 vari: 2g dtb 1 soc: gxm plat: q201 vari: 3g Find match dtb: 1 start dts,buffer=00000000b3e9d200,dt_addr=00000000b3ea9200 Amlogic multi-dtb tool Multi dtb detected edwin--->DDR size: 0xb8000000 Multi dtb tool version: v2 . Support 2 dtbs. aml_dt soc: gxm platform: q201 variant: 3g dtb 0 soc: gxm plat: q201 vari: 2g dtb 1 soc: gxm plat: q201 vari: 3g Find match dtb: 1 parts: 10 00: logo 0000000002000000 1 01: recovery 0000000002000000 1 02: rsv 0000000000800000 1 03: tee 0000000000800000 1 04: crypt 0000000002000000 1 05: misc 0000000002000000 1 06: boot 0000000002000000 1 07: system 0000000080000000 1 08: cache 0000000020000000 2 09: data ffffffffffffffff 4 init_part() 293: PART_TYPE_AML eMMC/TSD partition table have been checked OK! check pattern success mmc env offset: 0x27400000 In: serial Out: serial Err: serial reboot_mode=cold_boot hpd_state=0 cvbs performance type = 6, table = 0 [store]To run cmd[emmc dtb_read 0x1000000 0x40000] _verify_dtb_checksum()-917: calc 668a0968, store 668a0968 _verify_dtb_checksum()-917: calc 668a0968, store 668a0968 dtb_read()-1039: total valid 2 dtb_read()-1106: do nothing Amlogic multi-dtb tool Multi dtb detected edwin--->DDR size: 0xb8000000 Multi dtb tool version: v2 . Support 2 dtbs. aml_dt soc: gxm platform: q201 variant: 3g dtb 0 soc: gxm plat: q201 vari: 2g dtb 1 soc: gxm plat: q201 vari: 3g Find match dtb: 1 vpp: vpp_pq_load pq val error !!! Net: dwmac.c9410000amlkey_init() enter! [EFUSE_MSG]keynum is 4 [BL31]: tee size: 0 Start read misc partition datas! info->attemp_times = 0 info->active_slot = 0 info->slot_info[0].bootable = 1 info->slot_info[0].online = 1 info->slot_info[1].bootable = 0 info->slot_info[1].online = 0 info->attemp_times = 0 attemp_times = 0 active slot = 0 wipe_data=successful wipe_cache=successful upgrade_step=0 [OSD]load fb addr from dts [OSD]fb_addr for logo: 0x7f851000 [OSD]load fb addr from dts [OSD]fb_addr for logo: 0x7f851000 [CANVAS]addr=0x7f851000 width=3840, height=2160 amlkey_init() enter! amlkey_init() 71: already init! [EFUSE_MSG]keynum is 4 [BL31]: tee size: 0 [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet gpio: pin GPIOAO_2 (gpio 102) value is 1 Hit Enter or space or Ctrl+C key to stop autoboot -- : 0 gxm_q201_v1#