bumerc@bumerc-linux-server:~$ sudo kermit [sudo] Passwort für bumerc: Connecting to /dev/ttyUSB0, speed 115200 Escape character: Ctrl-\ (ASCII 28, FS): enabled Type the escape character followed by C to get back, or followed by ? to see other options. ---------------------------------------------------- GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RCY:0;EMMC:0;READ:0;CHK:AA;SD:0;READ:0;0.0;CHK:0; no sdio debug board detected TE: 235629 BL2 Built : 20:32:17, Sep 8 2017. gxl g6296b83 - xiaobo.gu@droid12 set vdd cpu_a to 1120 mv set vdd cpu_b to 1050 mv set vddee to 1000 mv Board ID = 1 CPU clk: 1200MHz DDR low power enabled DQS-corr enabled DDR scramble enabled STICKY_REG0: 0x00000000 STICKY_REG1: 0x00000000 STICKY_REG9: 0x00000000 LPDDR3 chl: Rank0+1 @ 792MHz DDR0_PUB_CATR0 1 value DDR0_PUB_CATR0: 0x00141020.... DDR0_PUB_CATR1: 0x0203aaaa.... DDR0_PUB_PGSR0: 0x8000003f.... Rank0: 2048MB(auto)-2T-3 Rank1: 1024MB(auto)-2T-3 DataBus test pass! AddrBus test pass! Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000 New fip structure! Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600 Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x0002c600 Load bl33 from SD, src: 0x00050200, des: 0x01000000, size: 0x00066600 NOTICE: BL3-1: v1.0(release):a625749 NOTICE: BL3-1: Built : 11:25:15, Aug 25 2017 NOTICE: BL31: BL33 decompress pass mpu_config_enable:ok [Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07] OPS=0x82 wdt: reset registers! b4 4b 34 87 31 36 df 54 9d 41 1f 65 [0.602058 Inits done] secure task start! high task start! low task start! ERROR: Error initializing runtime service opteed_fast U-Boot 2015.01-g2735815-dirty (Mar 16 2018 - 11:15:22) DRAM: 3 GiB Relocation Offset is: b6eb5000 register usb cfg[0][1] = 00000000b7f5ac50 [CANVAS]canvas init boot_device_flag : 1 Nand PHY Ver:1.01.001.0006 (c) 2013 Amlogic Inc. init bus_cycle=6, bus_timing=7, system=5.0ns reset failed get_chip_type and ret:fffffffe get_chip_type and ret:fffffffe chip detect failed and ret:fffffffe nandphy_init failed and ret=0xfffffff1 MMC: aml_priv->desc_buf = 0x00000000b3eb56b0 aml_priv->desc_buf = 0x00000000b3eb79d0 SDIO Port B: 0, SDIO Port C: 1 emmc/sd response timeout, cmd8, status=0x1ff2800 emmc/sd response timeout, cmd55, status=0x1ff2800 emmc/sd read error, cmd8, status=0x100a0ff emmc/sd read error, cmd8, status=0x1ff2003 emmc/sd read error, cmd8, status=0x1fca001 MMC init failed Using default environment In: serial Out: serial Err: serial reboot_mode=cold_boot [store]To run cmd[emmc dtb_read 0x1000000 0x40000] emmc/sd response timeout, cmd8, status=0x1ff2800 emmc/sd response timeout, cmd55, status=0x1ff2800 init_part() 293: PART_TYPE_AML [mmc_init] mmc init success dtb magic edfe0dd0 Amlogic multi-dtb tool Single dtb detected start dts,buffer=00000000b3ec1af0,dt_addr=00000000b3ec1af0 Amlogic multi-dtb tool Single dtb detected parts: 11 00: logo 0000000002000000 1 01: recovery 0000000002000000 1 02: rsv 0000000000800000 1 03: tee 0000000000800000 1 04: crypt 0000000002000000 1 05: misc 0000000002000000 1 06: instaboot 0000000020000000 1 07: boot 0000000002000000 1 08: system 0000000040000000 1 09: cache 0000000020000000 2 10: data ffffffffffffffff 4 init_part() 293: PART_TYPE_AML eMMC/TSD partition table have been checked OK! check pattern success _verify_dtb_checksum()-917: calc 0, store 0 dtb_read()-1034: cpy 1 is not valid _verify_dtb_checksum()-917: calc 0, store 0 dtb_read()-1034: cpy 0 is not valid dtb_read()-1039: total valid 0 Amlogic multi-dtb tool Cannot find legal dtb! [store]Err:do_store_dtb_ops,L330:Fail in fdt check header board_late_init(): [store dtb read $dtb_mem_addr] fail load dtb to 1000000 [store]To run cmd[emmc dtb_read 1000000 0x40000] _verify_dtb_checksum()-917: calc 7e0cea54, store 7e0cea54 _verify_dtb_checksum()-917: calc 7e0cea54, store 7e0cea54 dtb_read()-1039: total valid 2 dtb_read()-1106: do nothing Amlogic multi-dtb tool Single dtb detected vpu: clk_level in dts: 7 vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300) vpu: vpu_clk_gate_init_off vpp: vpp_init hpd_state=0 cvbs performance type = 6, table = 0 card in init_part() 278: PART_TYPE_DOS [mmc_init] mmc init success Device: SDIO Port B Manufacturer ID: 1b OEM: 534d Name: EB1QT Tran Speed: 50000000 Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 29.8 GiB mmc clock: 40000000 Bus Width: 4-bit vpp: vpp_pq_load pq val error !!! Net: dwmac.c9410000amlkey_init() enter! [EFUSE_MSG]keynum is 4 [BL31]: tee size: 0 Start read misc partition datas! info->attemp_times = 0 info->active_slot = 0 info->slot_info[0].bootable = 1 info->slot_info[0].online = 1 info->slot_info[1].bootable = 0 info->slot_info[1].online = 0 info->attemp_times = 0 attemp_times = 0 active slot = 0 wipe_data=successful wipe_cache=successful upgrade_step=0 [OSD]load fb addr from dts [OSD]fb_addr for logo: 0x7d851000 [OSD]load fb addr from dts [OSD]fb_addr for logo: 0x7d851000 [CANVAS]addr=0x7d851000 width=3840, height=2160 amlkey_init() enter! amlkey_init() 71: already init! [EFUSE_MSG]keynum is 4 [BL31]: tee size: 0 [KM]Error:f[key_manage_query_size]L507:key[usid] not programed yet [KM]Error:f[key_manage_query_size]L507:key[deviceid] not programed yet gpio: pin GPIOAO_2 (gpio 102) value is 1 Hit Enter or space or Ctrl+C key to stop autoboot -- : 0 gxm_q201_v1#store store - STORE sub-system Usage: store store init flag store read name addr off|partition size read 'size' bytes starting at offset 'off' to/from memory address 'addr', skipping bad blocks. store write name addr off|partition size write 'size' bytes starting at offset 'off' to/from memory address 'addr', skipping bad blocks. store rom_write add off size. write uboot to the boot device store erase boot/data: erase the area which is uboot or data store erase partition : erase the area which partition in u-boot store erase dtb store erase key store disprotect key store rom_protect on/off store scrub off|partition size scrub the area from offset and size store dtb iread/read/write addr read/write dtb, size is optional store key read/write addr read/write key, size is optional store mbr addr update mbr/partition table by dtb gxm_q201_v1#store erase boot emmckey_is_protected : protect start = 0,end = 8191 mmc switch to boot0 success emmckey_is_protected : protect blkcnt = 8192 start = 0,end = 8191 mmc switch to boot1 success emmckey_is_protected : protect blkcnt = 8192 start = 0,end = 8191 mmc switch to user success gxm_q201_v1#mmcinfo Device: SDIO Port B Manufacturer ID: 1b OEM: 534d Name: EB1QT Tran Speed: 50000000 Rd Block Len: 512 SD version 3.0 High Capacity: Yes Capacity: 29.8 GiB mmc clock: 40000000 Bus Width: 4-bit gxm_q201_v1#fatload mmc 0:1 0x01080000 u-boot.bin reading u-boot.bin 753664 bytes read in 46 ms (15.6 MiB/s) gxm_q201_v1#store rom_write 0x01080000 0 100000 mmc switch to boot0 success mmc switch to boot1 success mmc switch to user success gxm_q201_v1#defenv ## defenv_reserve gxm_q201_v1#saveenv Saving Environment to aml-storage... mmc env offset: 0x27400000 Writing to MMC(1)... done gxm_q201_v1#