LE-RPi5:~ # dmesg [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x414fd0b1] [ 0.000000] Linux version 6.6.28 (docker@fababab48455) (aarch64-libreelec-linux-gnu-gcc-13.2.0 (GCC) 13.2.0, GNU ld (GNU Binutils) 2.41) #1 SMP Thu Apr 25 11:30:41 UTC 2024 [ 0.000000] random: crng init done [ 0.000000] Machine model: Raspberry Pi 5 Model B Rev 1.0 [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000004000000, size 512 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] OF: reserved mem: 0x0000000004000000..0x0000000023ffffff (524288 KiB) map reusable linux,cma [ 0.000000] OF: reserved mem: 0x0000000000000000..0x000000000007ffff (512 KiB) nomap non-reusable atf@0 [ 0.000000] OF: reserved mem: 0x000000003fd16600..0x000000003fd16636 (0 KiB) nomap non-reusable nvram@0 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x00000000ffffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal [mem 0x0000000100000000-0x00000001ffffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000007ffff] [ 0.000000] node 0: [mem 0x0000000000080000-0x000000003fbfffff] [ 0.000000] node 0: [mem 0x0000000040000000-0x00000001ffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x00000001ffffffff] [ 0.000000] On node 0, zone DMA: 256 pages in unavailable ranges [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 14 pages/cpu s177320 r8192 d43864 u229376 [ 0.000000] pcpu-alloc: s177320 r8192 d43864 u229376 alloc=14*16384 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected PIPT I-cache on CPU0 [ 0.000000] CPU features: detected: Virtualization Host Extensions [ 0.000000] CPU features: detected: Hardware dirty bit management [ 0.000000] CPU features: detected: Spectre-v4 [ 0.000000] CPU features: detected: Spectre-BHB [ 0.000000] CPU features: kernel page table isolation forced OFF by mitigations=off [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: reboot=w coherent_pool=1M 8250.nr_uarts=1 pci=pcie_bus_safe snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 smsc95xx.macaddr=D8:3A:DD:E8:87:75 vc_mem.mem_base=0x3fc00000 vc_mem.mem_size=0x40000000 boot=UUID=2504-0815 disk=UUID=9f7b1397-4586-452d-a897-b3f9f95035f5 quiet console=ttyAMA10,115200 console=tty0 [ 0.000000] Unknown kernel command line parameters "boot=UUID=2504-0815 disk=UUID=9f7b1397-4586-452d-a897-b3f9f95035f5", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 1048576 (order: 9, 8388608 bytes, linear) [ 0.000000] Inode-cache hash table entries: 524288 (order: 8, 4194304 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 521984 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: mapped [mem 0x00000000fbffc000-0x00000000ffffc000] (64MB) [ 0.000000] Memory: 7711568K/8384512K available (13632K kernel code, 2214K rwdata, 3920K rodata, 10432K init, 862K bss, 148656K reserved, 524288K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 43889 entries in 43 pages [ 0.000000] ftrace: allocated 43 pages with 4 groups [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 54.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xc743ce346, max_idle_ns: 440795203123 ns [ 0.000000] sched_clock: 56 bits at 54MHz, resolution 18ns, wraps every 4398046511102ns [ 0.000156] Console: colour dummy device 80x25 [ 0.000161] printk: console [tty0] enabled [ 0.000192] Calibrating delay loop (skipped), value calculated using timer frequency.. 108.50 BogoMIPS (lpj=180000) [ 0.000197] pid_max: default: 32768 minimum: 301 [ 0.000253] Mount-cache hash table entries: 16384 (order: 3, 131072 bytes, linear) [ 0.000275] Mountpoint-cache hash table entries: 16384 (order: 3, 131072 bytes, linear) [ 0.000598] cgroup: Disabling memory control group subsystem [ 0.000711] spectre-v4 mitigation disabled by command-line option [ 0.000982] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.001004] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1. [ 0.001060] rcu: Hierarchical SRCU implementation. [ 0.001061] rcu: Max phase no-delay instances is 1000. [ 0.001690] EFI services will not be available. [ 0.001759] smp: Bringing up secondary CPUs ... [ 0.001897] Detected PIPT I-cache on CPU1 [ 0.001941] CPU1: Booted secondary processor 0x0000000100 [0x414fd0b1] [ 0.002098] Detected PIPT I-cache on CPU2 [ 0.002130] CPU2: Booted secondary processor 0x0000000200 [0x414fd0b1] [ 0.002289] Detected PIPT I-cache on CPU3 [ 0.002316] CPU3: Booted secondary processor 0x0000000300 [0x414fd0b1] [ 0.002341] smp: Brought up 1 node, 4 CPUs [ 0.002346] SMP: Total of 4 processors activated. [ 0.002349] CPU features: detected: 32-bit EL0 Support [ 0.002350] CPU features: detected: Data cache clean to the PoU not required for I/D coherence [ 0.002352] CPU features: detected: Common not Private translations [ 0.002354] CPU features: detected: CRC32 instructions [ 0.002356] CPU features: detected: RCpc load-acquire (LDAPR) [ 0.002357] CPU features: detected: LSE atomic instructions [ 0.002359] CPU features: detected: Privileged Access Never [ 0.002360] CPU features: detected: RAS Extension Support [ 0.002363] CPU features: detected: Speculative Store Bypassing Safe (SSBS) [ 0.002380] spectre-bhb mitigation disabled by command line option [ 0.002381] spectre-bhb mitigation disabled by command line option [ 0.002398] CPU: All CPU(s) started at EL2 [ 0.002399] alternatives: applying system-wide alternatives [ 0.003813] devtmpfs: initialized [ 0.006654] Enabled cp15_barrier support [ 0.006659] Enabled setend support [ 0.006714] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns [ 0.006719] futex hash table entries: 1024 (order: 2, 65536 bytes, linear) [ 0.008009] pinctrl core: initialized pinctrl subsystem [ 0.008164] DMI not present or invalid. [ 0.008257] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.008839] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations [ 0.008883] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.008928] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.009052] thermal_sys: Registered thermal governor 'step_wise' [ 0.009066] cpuidle: using governor menu [ 0.009127] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.009151] ASID allocator initialised with 65536 entries [ 0.009465] Serial: AMBA PL011 UART driver [ 0.010295] bcm2835-mbox 107c013880.mailbox: mailbox enabled [ 0.010624] 107d001000.serial: ttyAMA10 at MMIO 0x107d001000 (irq = 15, base_baud = 0) is a PL011 rev2 [ 0.010634] printk: console [ttyAMA10] enabled [ 0.016828] raspberrypi-firmware soc:firmware: Attached to firmware from 2024-04-20T10:53:30, variant start_cd [ 0.020164] raspberrypi-firmware soc:firmware: Firmware hash is d1744d2100000000000000000000000000000000 [ 0.025625] Modules: 6236 pages in range for non-PLT usage [ 0.025628] Modules: 129116 pages in range for PLT usage [ 0.031055] cryptd: max_cpu_qlen set to 1000 [ 0.031688] iommu: Default domain type: Translated [ 0.031691] iommu: DMA domain TLB invalidation policy: strict mode [ 0.031761] SCSI subsystem initialized [ 0.031798] usbcore: registered new interface driver usbfs [ 0.031806] usbcore: registered new interface driver hub [ 0.031814] usbcore: registered new device driver usb [ 0.031974] Advanced Linux Sound Architecture Driver Initialized. [ 0.032194] vgaarb: loaded [ 0.032284] clocksource: Switched to clocksource arch_sys_counter [ 0.032466] FS-Cache: Loaded [ 0.034737] NET: Registered PF_INET protocol family [ 0.034884] IP idents hash table entries: 131072 (order: 6, 1048576 bytes, linear) [ 0.037494] tcp_listen_portaddr_hash hash table entries: 4096 (order: 2, 65536 bytes, linear) [ 0.037546] Table-perturb hash table entries: 65536 (order: 4, 262144 bytes, linear) [ 0.037552] TCP established hash table entries: 65536 (order: 5, 524288 bytes, linear) [ 0.037666] TCP bind hash table entries: 65536 (order: 7, 2097152 bytes, linear) [ 0.039277] TCP: Hash tables configured (established 65536 bind 65536) [ 0.039344] UDP hash table entries: 4096 (order: 3, 131072 bytes, linear) [ 0.039382] UDP-Lite hash table entries: 4096 (order: 3, 131072 bytes, linear) [ 0.039478] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.039619] RPC: Registered named UNIX socket transport module. [ 0.039621] RPC: Registered udp transport module. [ 0.039623] RPC: Registered tcp transport module. [ 0.039624] RPC: Registered tcp-with-tls transport module. [ 0.039626] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.039630] PCI: CLS 0 bytes, default 64 [ 0.301925] Initialise system trusted keyrings [ 0.302021] workingset: timestamp_bits=46 max_order=19 bucket_order=0 [ 0.302208] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.302332] NFS: Registering the id_resolver key type [ 0.302339] Key type id_resolver registered [ 0.302340] Key type id_legacy registered [ 0.302346] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.302349] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.302509] Key type cifs.idmap registered [ 0.313739] NET: Registered PF_ALG protocol family [ 0.313743] Key type asymmetric registered [ 0.313745] Asymmetric key parser 'x509' registered [ 0.313759] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 0.313794] io scheduler mq-deadline registered [ 0.313796] io scheduler kyber registered [ 0.313803] io scheduler bfq registered [ 0.314007] irq_brcmstb_l2: registered L2 intc (/soc/interrupt-controller@7c502000, parent irq: 27) [ 0.314063] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d503000, parent irq: 28) [ 0.314101] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d508380, parent irq: 29) [ 0.314144] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d508400, parent irq: 30) [ 0.314183] irq_brcmstb_l2: registered L2 intc (/soc/interrupt-controller@7d510600, parent irq: 31) [ 0.314220] irq_brcmstb_l2: registered L2 intc (/soc/intc@7d517b00, parent irq: 32) [ 0.349699] Serial: 8250/16550 driver, 1 ports, IRQ sharing enabled [ 0.350070] 107d50c000.serial: ttyS0 at MMIO 0x107d50c000 (irq = 34, base_baud = 6000000) is a Broadcom BCM7271 UART [ 0.350130] serial serial0: tty port ttyS0 registered [ 0.350352] iproc-rng200 107d208000.rng: hwrng registered [ 0.350492] rpi-gpiomem 107d508500.gpiomem: window base 0x107d508500 size 0x00000040 [ 0.350520] rpi-gpiomem 107d508500.gpiomem: initialised 1 regions as /dev/gpiomem1 [ 0.350542] rpi-gpiomem 107d517c00.gpiomem: window base 0x107d517c00 size 0x00000040 [ 0.350563] rpi-gpiomem 107d517c00.gpiomem: initialised 1 regions as /dev/gpiomem2 [ 0.350582] rpi-gpiomem 107d504100.gpiomem: window base 0x107d504100 size 0x00000020 [ 0.350606] rpi-gpiomem 107d504100.gpiomem: initialised 1 regions as /dev/gpiomem3 [ 0.350625] rpi-gpiomem 107d510700.gpiomem: window base 0x107d510700 size 0x00000020 [ 0.350646] rpi-gpiomem 107d510700.gpiomem: initialised 1 regions as /dev/gpiomem4 [ 0.350768] bcm2712-iommu-cache 1000005b00.iommuc: bcm2712_iommu_cache_probe [ 0.353536] brd: module loaded [ 0.353558] loop: module loaded [ 0.358314] usbcore: registered new interface driver rtsx_usb [ 0.358478] bcm2835-power bcm2835-power: Broadcom BCM2835 power domains driver [ 0.359280] tun: Universal TUN/TAP device driver, 1.6 [ 0.359482] usbcore: registered new interface driver lan78xx [ 0.359488] usbcore: registered new interface driver dm9601 [ 0.359501] usbcore: registered new interface driver smsc95xx [ 0.359560] dwc_otg: version 3.00a 10-AUG-2012 (platform bus) [ 0.359579] dwc_otg: FIQ enabled [ 0.359581] dwc_otg: NAK holdoff enabled [ 0.359582] dwc_otg: FIQ split-transaction FSM enabled [ 0.359585] Module dwc_common_port init [ 0.359806] usbcore: registered new interface driver uas [ 0.359814] usbcore: registered new interface driver usb-storage [ 0.359878] mousedev: PS/2 mouse device common for all mice [ 0.368313] rpi-rtc soc:rpi_rtc: registered as rtc0 [ 0.369838] rpi-rtc soc:rpi_rtc: setting system clock to 2024-08-31T05:19:37 UTC (1725081577) [ 0.369866] i2c_dev: i2c /dev entries driver [ 0.370035] brcmstb-i2c 107d508200.i2c: @97500hz registered in interrupt mode [ 0.370129] brcmstb-i2c 107d508280.i2c: @97500hz registered in interrupt mode [ 0.370505] bcm2835-wdt bcm2835-wdt: Poweroff handler already present! [ 0.370508] bcm2835-wdt bcm2835-wdt: Broadcom BCM2835 watchdog timer [ 0.372896] sdhci: Secure Digital Host Controller Interface driver [ 0.372899] sdhci: Copyright(c) Pierre Ossman [ 0.372918] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.373114] ledtrig-cpu: registered to indicate activity on CPUs [ 0.373150] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping .... [ 0.373161] hid: raw HID events driver (C) Jiri Kosina [ 0.373401] usbcore: registered new interface driver usbhid [ 0.373403] usbhid: USB HID core driver [ 0.373676] hw perfevents: enabled with armv8_cortex_a76 PMU driver, 7 counters available [ 0.374094] Initializing XFRM netlink socket [ 0.374125] NET: Registered PF_INET6 protocol family [ 0.374371] Segment Routing with IPv6 [ 0.374378] In-situ OAM (IOAM) with IPv6 [ 0.374398] NET: Registered PF_PACKET protocol family [ 0.374407] Key type dns_resolver registered [ 0.378592] Loading compiled-in X.509 certificates [ 0.380915] brcm-pcie 1000110000.pcie: host bridge /axi/pcie@110000 ranges: [ 0.380922] brcm-pcie 1000110000.pcie: No bus range found for /axi/pcie@110000, using [bus 00-ff] [ 0.380929] brcm-pcie 1000110000.pcie: MEM 0x1b00000000..0x1bfffffffb -> 0x0000000000 [ 0.380934] brcm-pcie 1000110000.pcie: MEM 0x1800000000..0x1affffffff -> 0x0400000000 [ 0.380937] brcm-pcie 1000110000.pcie: IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000 [ 0.382235] brcm-pcie 1000110000.pcie: Forcing gen 2 [ 0.382446] brcm-pcie 1000110000.pcie: PCI host bridge to bus 0000:00 [ 0.382448] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.382450] pci_bus 0000:00: root bus resource [mem 0x1b00000000-0x1bfffffffb] (bus address [0x00000000-0xfffffffb]) [ 0.382453] pci_bus 0000:00: root bus resource [mem 0x1800000000-0x1affffffff pref] (bus address [0x400000000-0x6ffffffff]) [ 0.382462] pci 0000:00:00.0: [14e4:2712] type 01 class 0x060400 [ 0.382482] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.383029] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.488958] brcm-pcie 1000110000.pcie: link up, 5.0 GT/s PCIe x1 (!SSC) [ 0.488985] pci 0000:01:00.0: [15b7:5008] type 00 class 0x010802 [ 0.489005] pci 0000:01:00.0: reg 0x10: [mem 0x1b00000000-0x1b00003fff 64bit] [ 0.489029] pci 0000:01:00.0: reg 0x20: [mem 0x1b00000000-0x1b000000ff 64bit] [ 0.489157] pci 0000:01:00.0: 4.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x1 link at 0000:00:00.0 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link) [ 0.498974] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.498986] pci 0000:00:00.0: BAR 8: assigned [mem 0x1b00000000-0x1b000fffff] [ 0.498990] pci 0000:01:00.0: BAR 0: assigned [mem 0x1b00000000-0x1b00003fff 64bit] [ 0.499001] pci 0000:01:00.0: BAR 4: assigned [mem 0x1b00004000-0x1b000040ff 64bit] [ 0.499011] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.499014] pci 0000:00:00.0: bridge window [mem 0x1b00000000-0x1b000fffff] [ 0.499019] pci 0000:00:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 0.499028] pci 0000:01:00.0: Max Payload Size set to 512/ 512 (was 128), Max Read Rq 512 [ 0.499091] pcieport 0000:00:00.0: enabling device (0000 -> 0002) [ 0.499126] pcieport 0000:00:00.0: PME: Signaling with IRQ 41 [ 0.499199] pcieport 0000:00:00.0: AER: enabled with IRQ 41 [ 0.499335] nvme nvme0: pci function 0000:01:00.0 [ 0.499351] nvme 0000:01:00.0: enabling device (0000 -> 0002) [ 0.506630] nvme nvme0: allocated 128 MiB host memory buffer. [ 0.507292] nvme nvme0: 4/0/0 default/read/poll queues [ 0.510150] nvme0n1: p1 p2 [ 0.510283] brcm-pcie 1000110000.pcie: clkreq control enabled [ 0.510355] brcm-pcie 1000120000.pcie: host bridge /axi/pcie@120000 ranges: [ 0.510359] brcm-pcie 1000120000.pcie: No bus range found for /axi/pcie@120000, using [bus 00-ff] [ 0.510368] brcm-pcie 1000120000.pcie: MEM 0x1f00000000..0x1ffffffffb -> 0x0000000000 [ 0.510374] brcm-pcie 1000120000.pcie: MEM 0x1c00000000..0x1effffffff -> 0x0400000000 [ 0.510381] brcm-pcie 1000120000.pcie: IB MEM 0x1f00000000..0x1f003fffff -> 0x0000000000 [ 0.510385] brcm-pcie 1000120000.pcie: IB MEM 0x0000000000..0x0fffffffff -> 0x1000000000 [ 0.511461] brcm-pcie 1000120000.pcie: Forcing gen 2 [ 0.511498] brcm-pcie 1000120000.pcie: PCI host bridge to bus 0001:00 [ 0.511500] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.511503] pci_bus 0001:00: root bus resource [mem 0x1f00000000-0x1ffffffffb] (bus address [0x00000000-0xfffffffb]) [ 0.511506] pci_bus 0001:00: root bus resource [mem 0x1c00000000-0x1effffffff pref] (bus address [0x400000000-0x6ffffffff]) [ 0.511516] pci 0001:00:00.0: [14e4:2712] type 01 class 0x060400 [ 0.511540] pci 0001:00:00.0: PME# supported from D0 D3hot [ 0.512255] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.615624] brcm-pcie 1000120000.pcie: link up, 5.0 GT/s PCIe x4 (!SSC) [ 0.615645] pci 0001:01:00.0: [1de4:0001] type 00 class 0x020000 [ 0.615659] pci 0001:01:00.0: reg 0x10: [mem 0xffffc000-0xffffffff] [ 0.615666] pci 0001:01:00.0: reg 0x14: [mem 0xffc00000-0xffffffff] [ 0.615673] pci 0001:01:00.0: reg 0x18: [mem 0xffff0000-0xffffffff] [ 0.615743] pci 0001:01:00.0: supports D1 [ 0.615745] pci 0001:01:00.0: PME# supported from D0 D1 D3hot D3cold [ 0.625628] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.625637] pci 0001:00:00.0: BAR 8: assigned [mem 0x1f00000000-0x1f005fffff] [ 0.625641] pci 0001:01:00.0: BAR 1: assigned [mem 0x1f00000000-0x1f003fffff] [ 0.625646] pci 0001:01:00.0: BAR 2: assigned [mem 0x1f00400000-0x1f0040ffff] [ 0.625651] pci 0001:01:00.0: BAR 0: assigned [mem 0x1f00410000-0x1f00413fff] [ 0.625656] pci 0001:00:00.0: PCI bridge to [bus 01] [ 0.625659] pci 0001:00:00.0: bridge window [mem 0x1f00000000-0x1f005fffff] [ 0.625663] pci 0001:00:00.0: Max Payload Size set to 256/ 512 (was 128), Max Read Rq 512 [ 0.625672] pci 0001:01:00.0: Max Payload Size set to 256/ 256 (was 128), Max Read Rq 512 [ 0.625728] pcieport 0001:00:00.0: enabling device (0000 -> 0002) [ 0.625761] pcieport 0001:00:00.0: PME: Signaling with IRQ 47 [ 0.625827] pcieport 0001:00:00.0: AER: enabled with IRQ 47 [ 0.625902] rp1 0001:01:00.0: bar0 len 0x4000, start 0x1f00410000, end 0x1f00413fff, flags, 0x40200 [ 0.625906] rp1 0001:01:00.0: bar1 len 0x400000, start 0x1f00000000, end 0x1f003fffff, flags, 0x40200 [ 0.625916] rp1 0001:01:00.0: enabling device (0000 -> 0002) [ 0.626642] rp1 0001:01:00.0: chip_id 0x20001927 [ 0.631268] genirq: irq_chip rp1_irq_chip did not update eff. affinity mask of irq 109 [ 0.644292] macb 1f00100000.ethernet eth0: Cadence GEM rev 0x00070109 at 0x1f00100000 irq 115 (d8:3a:dd:e8:87:75) [ 0.644755] dw_axi_dmac_platform 1f00188000.dma: DesignWare AXI DMA Controller, 8 channels [ 0.644971] xhci-hcd xhci-hcd.0: xHCI Host Controller [ 0.644976] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1 [ 0.665588] xhci-hcd xhci-hcd.0: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000008000000810 [ 0.665598] xhci-hcd xhci-hcd.0: irq 140, io mem 0x1f00200000 [ 0.665660] xhci-hcd xhci-hcd.0: xHCI Host Controller [ 0.665662] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2 [ 0.665666] xhci-hcd xhci-hcd.0: Host supports USB 3.0 SuperSpeed [ 0.665712] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06 [ 0.665715] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.665717] usb usb1: Product: xHCI Host Controller [ 0.665718] usb usb1: Manufacturer: Linux 6.6.28 xhci-hcd [ 0.665720] usb usb1: SerialNumber: xhci-hcd.0 [ 0.665824] hub 1-0:1.0: USB hub found [ 0.665836] hub 1-0:1.0: 2 ports detected [ 0.665941] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06 [ 0.665943] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.665945] usb usb2: Product: xHCI Host Controller [ 0.665947] usb usb2: Manufacturer: Linux 6.6.28 xhci-hcd [ 0.665948] usb usb2: SerialNumber: xhci-hcd.0 [ 0.666013] hub 2-0:1.0: USB hub found [ 0.666022] hub 2-0:1.0: 1 port detected [ 0.666237] xhci-hcd xhci-hcd.1: xHCI Host Controller [ 0.666241] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3 [ 0.666675] xhci-hcd xhci-hcd.1: hcc params 0x0240fe6d hci version 0x110 quirks 0x0000008000000810 [ 0.666684] xhci-hcd xhci-hcd.1: irq 145, io mem 0x1f00300000 [ 0.666735] xhci-hcd xhci-hcd.1: xHCI Host Controller [ 0.666738] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4 [ 0.666740] xhci-hcd xhci-hcd.1: Host supports USB 3.0 SuperSpeed [ 0.666767] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.06 [ 0.666770] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.666772] usb usb3: Product: xHCI Host Controller [ 0.666773] usb usb3: Manufacturer: Linux 6.6.28 xhci-hcd [ 0.666775] usb usb3: SerialNumber: xhci-hcd.1 [ 0.666841] hub 3-0:1.0: USB hub found [ 0.666852] hub 3-0:1.0: 2 ports detected [ 0.666937] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.06 [ 0.666939] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.666941] usb usb4: Product: xHCI Host Controller [ 0.666942] usb usb4: Manufacturer: Linux 6.6.28 xhci-hcd [ 0.666944] usb usb4: SerialNumber: xhci-hcd.1 [ 0.667006] hub 4-0:1.0: USB hub found [ 0.667015] hub 4-0:1.0: 1 port detected [ 0.667128] rpi-gpiomem 1f000d0000.gpiomem: window base 0x1f000d0000 size 0x00030000 [ 0.667153] rpi-gpiomem 1f000d0000.gpiomem: initialised 1 regions as /dev/gpiomem0 [ 0.667538] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774 [ 0.667813] platform 1000800000.codec: bcm2712_iommu_probe_device: MMU 1000005100.iommu [ 0.667817] platform 1000800000.codec: bcm2712_iommu_device_group: MMU 1000005100.iommu [ 0.667820] platform 1000800000.codec: Adding to iommu group 0 [ 0.667829] platform 1000880000.pisp_be: bcm2712_iommu_probe_device: MMU 1000005100.iommu [ 0.667832] platform 1000880000.pisp_be: bcm2712_iommu_device_group: MMU 1000005100.iommu [ 0.667834] platform 1000880000.pisp_be: Adding to iommu group 0 [ 0.667853] platform 1000800000.codec: bcm2712_iommu_attach_dev: MMU 1000005100.iommu [ 0.667855] platform 1000880000.pisp_be: bcm2712_iommu_attach_dev: MMU 1000005100.iommu [ 0.667858] bcm2712-iommu 1000005100.iommu: bcm2712_iommu_probe: Success [ 0.668093] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774 [ 0.668298] platform axi:gpu: bcm2712_iommu_probe_device: MMU 1000005200.iommu [ 0.668300] platform axi:gpu: bcm2712_iommu_device_group: MMU 1000005200.iommu [ 0.668303] platform axi:gpu: Adding to iommu group 1 [ 0.668314] platform axi:gpu: bcm2712_iommu_attach_dev: MMU 1000005200.iommu [ 0.668317] bcm2712-iommu 1000005200.iommu: bcm2712_iommu_probe: Success [ 0.668585] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_init: DEBUG_INFO = 0x20804774 [ 0.668795] bcm2712-iommu 1000005280.iommu: bcm2712_iommu_probe: Success [ 0.673672] [drm] Initialized v3d 1.0.0 20180419 for 1002000000.v3d on minor 0 [ 0.680740] vc4-drm axi:gpu: bcm2712_iommu_of_xlate: MMU 1000005200.iommu [ 0.683105] vc4-drm axi:gpu: bound 107c580000.hvs (ops 0xffffc00080e276c0) [ 0.684601] input: vc4-hdmi-0 HDMI Jack as /devices/platform/soc/107c701400.hdmi/sound/card0/input0 [ 0.687757] vc4-drm axi:gpu: bound 107c701400.hdmi (ops 0xffffc00080e23d28) [ 0.689477] input: vc4-hdmi-1 HDMI Jack as /devices/platform/soc/107c706400.hdmi/sound/card1/input1 [ 0.689522] vc4-drm axi:gpu: bound 107c706400.hdmi (ops 0xffffc00080e23d28) [ 0.689574] vc4-drm axi:gpu: bound 107c500000.mop (ops 0xffffc00080e28aa0) [ 0.689608] vc4-drm axi:gpu: bound 107c501000.moplet (ops 0xffffc00080e28aa0) [ 0.689641] vc4-drm axi:gpu: bound 107c410000.pixelvalve (ops 0xffffc00080e20d50) [ 0.689673] vc4-drm axi:gpu: bound 107c411000.pixelvalve (ops 0xffffc00080e20d50) [ 0.690031] [drm] Initialized vc4 0.0.0 20140616 for axi:gpu on minor 1 [ 0.833333] Console: switching to colour frame buffer device 480x135 [ 0.855997] vc4-drm axi:gpu: [drm] fb0: vc4drmfb frame buffer device [ 0.857162] sdhci-brcmstb 1000fff000.mmc: Got CD GPIO [ 0.857634] mmc1: CQHCI version 5.10 [ 0.858086] printk: console [netcon0] enabled [ 0.858089] netconsole: network logging started [ 0.858096] of_cfs_init [ 0.858116] of_cfs_init: OK [ 0.858178] clk: Disabling unused clocks [ 0.864188] ALSA device list: [ 0.864190] #0: vc4-hdmi-0 [ 0.864192] #1: vc4-hdmi-1 [ 0.893457] mmc0: SDHCI controller on 1000fff000.mmc [1000fff000.mmc] using ADMA 64-bit [ 0.915681] usb 1-1: new high-speed USB device number 2 using xhci-hcd [ 0.985353] mmc0: new ultra high speed SDR104 SDXC card at address 5048 [ 0.985600] mmcblk0: mmc0:5048 SDCHE 58.0 GiB [ 0.986667] mmcblk0: p1 p2 [ 0.986740] mmcblk0: mmc0:5048 SDCHE 58.0 GiB [ 1.042825] mmc1: SDHCI controller on 1001100000.mmc [1001100000.mmc] using ADMA 64-bit [ 1.049480] Freeing unused kernel memory: 10432K [ 1.049665] Run /init as init process [ 1.049671] with arguments: [ 1.049674] /init [ 1.049677] with environment: [ 1.049678] HOME=/ [ 1.049680] TERM=linux [ 1.049682] boot=UUID=2504-0815 [ 1.049684] disk=UUID=9f7b1397-4586-452d-a897-b3f9f95035f5 [ 1.064089] usb 1-1: New USB device found, idVendor=2109, idProduct=2817, bcdDevice= 7.64 [ 1.064098] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.064101] usb 1-1: Product: USB2.0 Hub [ 1.064104] usb 1-1: Manufacturer: VIA Labs, Inc. [ 1.080910] mmc1: new ultra high speed DDR50 SDIO card at address 0001 [ 1.113887] hub 1-1:1.0: USB hub found [ 1.114212] hub 1-1:1.0: 4 ports detected [ 1.129041] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd [ 1.132093] Checking disk(s): UUID=2504-0815 UUID=9f7b1397-4586-452d-a897-b3f9f95035f5 [ 1.152536] usb 4-1: New USB device found, idVendor=0480, idProduct=a208, bcdDevice= 1.07 [ 1.152543] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1.152546] usb 4-1: Product: External USB 3.0 [ 1.152548] usb 4-1: Manufacturer: TOSHIBA [ 1.152550] usb 4-1: SerialNumber: 20140729021321 [ 1.153597] usb-storage 4-1:1.0: USB Mass Storage device detected [ 1.153701] scsi host0: usb-storage 4-1:1.0 [ 1.207204] fsck: fsck.fat 4.2 (2021-01-31) [ 1.207243] fsck: /dev/nvme0n1p1: 365 files, 18608/65501 clusters [ 1.207286] fsck: STORAGE: clean, 15366/62384128 files, 16582926/249530704 blocks [ 1.208983] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd [ 1.329368] usb 2-1: New USB device found, idVendor=2109, idProduct=0817, bcdDevice= 7.64 [ 1.329399] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 1.329405] usb 2-1: Product: USB3.0 Hub [ 1.329408] usb 2-1: Manufacturer: VIA Labs, Inc. [ 1.384003] loop0: detected capacity change from 0 to 267200 [ 1.385902] hub 2-1:1.0: USB hub found [ 1.386232] hub 2-1:1.0: 4 ports detected [ 1.443011] EXT4-fs (nvme0n1p2): mounted filesystem 9f7b1397-4586-452d-a897-b3f9f95035f5 r/w with ordered data mode. Quota mode: disabled. [ 1.905622] usb 1-1.4: new high-speed USB device number 3 using xhci-hcd [ 2.049126] usb 1-1.4: New USB device found, idVendor=2109, idProduct=2817, bcdDevice= 7.63 [ 2.049131] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.049134] usb 1-1.4: Product: USB2.0 Hub [ 2.049136] usb 1-1.4: Manufacturer: VIA Labs, Inc. [ 2.105904] hub 1-1.4:1.0: USB hub found [ 2.106379] hub 1-1.4:1.0: 4 ports detected [ 2.137958] usb 2-1.4: new SuperSpeed USB device number 3 using xhci-hcd [ 2.166927] scsi 0:0:0:0: Direct-Access TOSHIBA External USB 3.0 5438 PQ: 0 ANSI: 6 [ 2.274035] sd 0:0:0:0: [sda] 1953525164 512-byte logical blocks: (1.00 TB/932 GiB) [ 2.274381] sd 0:0:0:0: [sda] Write Protect is off [ 2.274385] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00 [ 2.274727] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.277444] sda: sda1 [ 2.277506] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.302512] usb 2-1.4: New USB device found, idVendor=2109, idProduct=0817, bcdDevice= 7.63 [ 2.302515] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 2.302518] usb 2-1.4: Product: USB3.0 Hub [ 2.302521] usb 2-1.4: Manufacturer: VIA Labs, Inc. [ 2.374133] hub 2-1.4:1.0: USB hub found [ 2.374888] hub 2-1.4:1.0: 4 ports detected [ 2.892302] usb 1-1.4.1: new full-speed USB device number 4 using xhci-hcd [ 3.045419] usb 1-1.4.1: New USB device found, idVendor=20a0, idProduct=0006, bcdDevice= 2.00 [ 3.045425] usb 1-1.4.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.045427] usb 1-1.4.1: Product: flirc [ 3.045430] usb 1-1.4.1: Manufacturer: flirc.tv [ 3.045433] usb 1-1.4.1: SerialNumber: C78053F250523939352E314BFF090B0B [ 3.232275] hid-generic 0003:20A0:0006.0001: hiddev96,hidraw0: USB HID v1.11 Device [flirc.tv flirc] on usb-xhci-hcd.0-1.4.1/input0 [ 3.257913] input: flirc.tv flirc Keyboard as /devices/platform/axi/1000120000.pcie/1f00200000.usb/xhci-hcd.0/usb1/1-1/1-1.4/1-1.4.1/1-1.4.1:1.1/0003:20A0:0006.0002/input/input2 [ 3.312375] hid-generic 0003:20A0:0006.0002: input,hidraw1: USB HID v1.01 Keyboard [flirc.tv flirc] on usb-xhci-hcd.0-1.4.1/input1 [ 3.318058] hid-generic 0003:20A0:0006.0003: hiddev97,hidraw2: USB HID v1.11 Device [flirc.tv flirc] on usb-xhci-hcd.0-1.4.1/input2 [ 3.442286] usb 1-1.4.2: new full-speed USB device number 5 using xhci-hcd [ 3.589693] usb 1-1.4.2: New USB device found, idVendor=046d, idProduct=c52b, bcdDevice=24.01 [ 3.589698] usb 1-1.4.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.589701] usb 1-1.4.2: Product: USB Receiver [ 3.589703] usb 1-1.4.2: Manufacturer: Logitech [ 3.716773] logitech-djreceiver 0003:046D:C52B.0006: hiddev98,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-xhci-hcd.0-1.4.2/input2 [ 3.838216] input: Logitech K400 Plus as /devices/platform/axi/1000120000.pcie/1f00200000.usb/xhci-hcd.0/usb1/1-1/1-1.4/1-1.4.2/1-1.4.2:1.2/0003:046D:C52B.0006/0003:046D:404D.0007/input/input3 [ 3.838368] logitech-hidpp-device 0003:046D:404D.0007: input,hidraw4: USB HID v1.11 Keyboard [Logitech K400 Plus] on usb-xhci-hcd.0-1.4.2/input2:1 [ 61.567449] kernel-overlays-setup: setup base modules [ 61.576341] kernel-overlays-setup: added firmware from /usr/lib/kernel-overlays/base/lib/firmware [ 61.576818] kernel-overlays-setup: adding overlays from /storage/.cache/kernel-overlays [ 61.578855] kernel-overlays-setup: added firmware from /storage/.config/firmware [ 61.578873] kernel-overlays-setup: done [ 61.632867] systemd[1]: systemd 255.4 running in system mode (-PAM -AUDIT -SELINUX -APPARMOR -IMA -SMACK -SECCOMP -GCRYPT -GNUTLS -OPENSSL -ACL +BLKID -CURL -ELFUTILS -FIDO2 +IDN2 -IDN -IPTC +KMOD -LIBCRYPTSETUP -LIBFDISK -PCRE2 -PWQUALITY -P11KIT -QRENCODE -TPM2 -BZIP2 -LZ4 -XZ -ZLIB -ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified) [ 61.632878] systemd[1]: Detected architecture arm64. [ 61.719433] systemd[1]: Queued start job for default target kodi.target. [ 61.743015] systemd[1]: Created slice system-modprobe.slice. [ 61.743228] systemd[1]: Created slice user.slice. [ 61.743295] systemd[1]: Started systemd-ask-password-console.path. [ 61.743337] systemd[1]: Started systemd-ask-password-wall.path. [ 61.743380] systemd[1]: Reached target paths.target. [ 61.743400] systemd[1]: Reached target slices.target. [ 61.746243] systemd[1]: Listening on rpcbind.socket. [ 61.746299] systemd[1]: Reached target rpcbind.target. [ 61.746397] systemd[1]: Listening on systemd-initctl.socket. [ 61.746696] systemd[1]: Listening on systemd-journald-dev-log.socket. [ 61.746828] systemd[1]: Listening on systemd-journald.socket. [ 61.747254] systemd[1]: Listening on systemd-udevd-control.socket. [ 61.747355] systemd[1]: Listening on systemd-udevd-kernel.socket. [ 61.750412] systemd[1]: Mounting dev-mqueue.mount... [ 61.751647] systemd[1]: Mounting sys-kernel-debug.mount... [ 61.752988] systemd[1]: Mounting sys-kernel-tracing.mount... [ 61.755658] systemd[1]: Mounting var.mount... [ 61.755912] systemd[1]: kmod-static-nodes.service was skipped because of an unmet condition check (ConditionFileNotEmpty=/lib/modules/6.6.28/modules.devname). [ 61.758909] systemd[1]: Starting machine-id.service... [ 61.762221] systemd[1]: Starting modprobe@configfs.service... [ 61.765403] systemd[1]: Starting modprobe@drm.service... [ 61.768753] systemd[1]: Starting modprobe@fuse.service... [ 61.770531] systemd[1]: Starting show-version.service... [ 61.774593] systemd[1]: Starting storage-log.service... [ 61.776842] systemd[1]: Starting swap.service... [ 61.781442] systemd[1]: Starting systemd-hwdb-update.service... [ 61.783001] systemd[1]: Starting systemd-modules-load.service... [ 61.786117] systemd[1]: Starting systemd-timesyncd-setup.service... [ 61.789758] systemd[1]: Starting systemd-tmpfiles-setup-dev-early.service... [ 61.795195] systemd[1]: Starting systemd-udev-trigger.service... [ 61.796482] systemd[1]: Starting wait-time-sync.service... [ 61.800091] systemd[1]: Mounted dev-mqueue.mount. [ 61.800223] systemd[1]: Mounted sys-kernel-debug.mount. [ 61.800313] systemd[1]: Mounted sys-kernel-tracing.mount. [ 61.800396] systemd[1]: Mounted var.mount. [ 61.800584] systemd[1]: Finished machine-id.service. [ 61.800831] systemd[1]: modprobe@configfs.service: Deactivated successfully. [ 61.800988] systemd[1]: Finished modprobe@configfs.service. [ 61.801299] systemd[1]: modprobe@drm.service: Deactivated successfully. [ 61.801407] systemd[1]: Finished modprobe@drm.service. [ 61.801670] systemd[1]: modprobe@fuse.service: Deactivated successfully. [ 61.801810] systemd[1]: Finished modprobe@fuse.service. [ 61.802074] systemd[1]: Finished show-version.service. [ 61.806288] systemd[1]: sys-fs-fuse-connections.mount was skipped because of an unmet condition check (ConditionPathExists=/sys/fs/fuse/connections). [ 61.809400] systemd[1]: Mounting sys-kernel-config.mount... [ 61.820964] systemd[1]: Starting systemd-journald.service... [ 61.821294] systemd[1]: Finished systemd-timesyncd-setup.service. [ 61.823718] systemd[1]: Finished storage-log.service. [ 61.823885] systemd[1]: Mounted sys-kernel-config.mount. [ 61.824583] systemd[1]: var-log.mount was skipped because no trigger condition checks were met. [ 61.831995] systemd[1]: Finished systemd-modules-load.service. [ 61.835028] systemd-journald[386]: Collecting audit messages is disabled. [ 61.836185] systemd[1]: Starting systemd-sysctl.service... [ 61.838811] systemd[1]: Finished systemd-tmpfiles-setup-dev-early.service. [ 61.841423] systemd[1]: Starting systemd-tmpfiles-setup-dev.service... [ 61.856114] systemd[1]: Finished systemd-tmpfiles-setup-dev.service. [ 61.856251] systemd[1]: Reached target local-fs-pre.target. [ 61.858906] systemd[1]: Finished systemd-sysctl.service. [ 61.867063] systemd[1]: Started systemd-journald.service. [ 61.887146] systemd-journald[386]: Received client request to flush runtime journal. [ 62.779561] EXT4-fs (mmcblk0p2): mounted filesystem 9f7b1397-4586-452d-a897-b3f9f95035f5 r/w with ordered data mode. Quota mode: disabled. [ 62.903760] macb 1f00100000.ethernet eth0: PHY [1f00100000.ethernet-ffffffff:01] driver [Broadcom BCM54213PE] (irq=POLL) [ 62.903787] macb 1f00100000.ethernet eth0: configuring for phy/rgmii-id link mode [ 66.960090] macb 1f00100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off LE-RPi5:~ # LE-RPi5:~ # lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 2109:2817 VIA Labs, Inc. USB2.0 Hub Bus 001 Device 003: ID 2109:2817 VIA Labs, Inc. USB2.0 Hub Bus 001 Device 004: ID 20a0:0006 Clay Logic flirc Bus 001 Device 005: ID 046d:c52b Logitech, Inc. Unifying Receiver Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 002: ID 2109:0817 VIA Labs, Inc. USB3.0 Hub Bus 002 Device 003: ID 2109:0817 VIA Labs, Inc. USB3.0 Hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 004 Device 002: ID 0480:a208 Toshiba America Inc Canvio Basics 2TB USB 3.0 Portable Hard Drive LE-RPi5:~ #