=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2024.07.23 11:09:04 =~=~=~=~=~=~=~=~=~=~=~= QA5:A;SVN:B72;POC:3DF;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;PASS:0; no sdio debug board detected TE : 24849 BT : 16:59:29 Sep 21 2015 PMU:NONE ##### VDDEE voltage = 0x044c CPU clock is 792MHz DDR mode: 16 bit mode lane0+2 DDR size: 1GB (auto) DDR check: Pass! DDR clock: 516MHz with 2T mode DDR pll bypass: Disabled DDR init use : 17107 us HHH ucl decompress...pass 0x12345678 Boot from internal device 1st NAND TE : 215628 System Started U-boot-00000-gfbec207-dirty(m8b_m201_v1@) (Sep 21 2015 - 16:59:17) clr h-ram DRAM: 1 GiB relocation Offset is: 2fec8000 show partition table: part: 0, name : logo, size : 2000000 part: 1, name : recovery, size : 2000000 part: 2, name : misc, size : 2000000 part: 3, name : boot, size : 2000000 part: 4, name : system, size : 40000000 part: 5, name : cache, size : 20000000 part: 6, name : data, size : end aml_card_type=0x100 MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6 [mmc_register] add mmc dev_num=1, port=2, if_type=6 SDIO Port B: 0, SDIO Port C: 1 power init out reg=c110804c,value=dfffffff IR init done! register usb cfg[0][1] = 3ff738cc register usb cfg[2][0] = 3ff76450 NAND: NAND BOOT: boot_device_flag 1 Nand PHY driver Version: 1.01.001.0004 (c) 2013 Amlogic Inc. amlnf_phy_init : amlnf init flag 0 NAND device id: 45 de 94 93 76 50 8 4 detect NAND device: A serials NAND 8GiB SDTNRGAMA-008G nand chip ce mask 1 AML_NAND_NEW_OOB : new oob bus_cycle=6, bus_timing=8,system=4.7ns,flash->T_REA =20,flash->T_RHOH=25 NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0 NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 0 NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 1 i=0,register --- nand_key NAND CKECK : arg nenv: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 30 nfboot : offset: 0x000000000000 -0x000001000000 : partitons 0 : single_chip single_plane nfcache : offset: 0x00000d000000 -0x000026000000 : partitons 1 : single_chip multi_plane nfcode : offset: 0x000033000000 -0x000057000000 : partitons 5 : single_chip multi_plane nfdata : offset: 0x00008a000000 -0x000176000000 : partitons 1 : single_chip multi_plane bad block count = 0 bad block count = 0 bad block count = 0 bad block count = 0 amlnf_logic_init: START amlnf_logic_init: COMPLETE get_boot_device_flag: init_ret 0 get_boot_device_flag NAND BOOT: NAND BOOT,nand_env_relocate_spec : env_relocate_spec 49 uboot env amlnf_env_read : #### set_storage_device_flag: store 1 vpu clk_level in dts: 3 set vpu clk: 182150000Hz, readback: 182150000Hz(0x701) Net: Meson_Ethernet init suspend firmware done. (ret:0) cvbs trimming.1.v5: 0xa0, 0x0 hdmi tx power init mode = 7 vic = 5 set HDMI vic: 5 mode is: 7 viu chan = 1 config HPLL config HPLL done reconfig packet setting done reboot_mode=charging update by key... Enter v2 usbburning mode Try connect time out 1001, 1000 [mmc_init] SDIO Port B:0, if_type=7, initialized OK! Device: SDIO Port B Manufacturer ID: 0 OEM: 0 Name: Tran Speed: 20000000 Rd Block Len: 512 SD version 2.0 High Capacity: Yes Capacity: 15634268160 Boot Part Size: 0 Bus Width: 4-bit ** Unable to open "aml_sdc_burn.ini" from mmc 0:1 --- file not exist** reading aml_autoscript 523 bytes read ## Executing script at 12000000 Saving Environment to NAND... NAND BOOT,nand_saveenv :saveenv 94 uboot env amlnf_env_save : #### size:65536 arg_pages:5 extra_page:1 nand_saveenv : Successful! Device: SDIO Port B Manufacturer ID: 0 OEM: 0 Name: Tran Speed: 20000000 Rd Block Len: 512 SD version 2.0 High Capacity: Yes Capacity: 15634268160 Boot Part Size: 0 Bus Width: 4-bit reading kernel.img 8177664 bytes read ## ANDROID Format IMAGE ## Booting kernel from Legacy Image at 12000000 ... Image Name: Linux-3.10.108 Image Type: ARM Linux Kernel Image (gzip compressed) Data Size: 4317041 Bytes = 4.1 MiB Load Address: 00208000 Entry Point: 00208000 Verifying Checksum ... OK Ramdisk start addr = 0x1241e800, len = 0x3a8800 Flat device tree start addr = 0x127c7000, len = 0x509a magic=0xedfe0dd0 Uncompressing Kernel Image ... OK uboot time: 5227376 us. EFUSE machid is not set. Using machid 0xf81 from environment From device tree /memory/ node aml_reserved_end property, for relocate ramdisk and fdt, relocate_addr: 0x53b2001 Loading Ramdisk to 05009000, end 053b1800 ... OK Loading Device Tree to 05000000, end 05008099 ... OK Starting kernel ... [ 0.000000@0] Booting Linux on physical CPU 0x200 [ 0.000000@0] Linux version 3.10.108 (dtech@LibreBuilder) (gcc version 8.3.0 (GCC) ) #1 SMP Thu Feb 29 15:13:41 CET 2024 [ 0.000000@0] CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c5387d [ 0.000000@0] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000@0] Machine: Amlogic Meson8B, model: AMLOGIC [ 0.000000@0] physical memory start address is 0x200000 [ 0.000000@0] reserved_end is bffffff [ 0.000000@0] [ 0.000000@0] Total memory is 1022 MiB [ 0.000000@0] Reserved low memory from 0x06000000 to 0x0bffffff, size: 96 MiB [ 0.000000@0] mesonfb0(low) : 0x06100000 - 0x07900000 ( 24 MiB) [ 0.000000@0] mesonfb1(low) : 0x07900000 - 0x07a00000 ( 1 MiB) [ 0.000000@0] deinterlace0(high) : 0x3df00000 - 0x40000000 ( 33 MiB) [ 0.000000@0] mesonstream0(high) : 0x3bf00000 - 0x3df00000 ( 32 MiB) [ 0.000000@0] vdec0(low) : 0x07a00000 - 0x0ba00000 ( 64 MiB) [ 0.000000@0] ppmgr0(high) : 0x39f00000 - 0x3bf00000 ( 32 MiB) [ 0.000000@0] amvideocap0(low) : 0x0ba00000 - 0x0c000000 ( 6 MiB) [ 0.000000@0] get storage device: storage 1 [ 0.000000@0] value=1 [ 0.000000@0] get_storage_device : get storage device: storage 1 [ 0.000000@0] get_storage_device : value=1 [ 0.000000@0] [get_storage_device] storage_flag=1 [ 0.000000@0] [get_storage_device] the storage device does NOT relate to eMMC, storage_flag=1 [ 0.000000@0] Memory policy: ECC disabled, Data cache writealloc [ 0.000000@0] Meson chip version = RevA (1B:A - 0:B72) [ 0.000000@0] PERCPU: Embedded 7 pages/cpu @c1215000 s7360 r8192 d13120 u32768 [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 207120 [ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200n8 no_console_suspend storage=1 vdaccfg=0xa000 logo=osd1,loaded,0x7900000,1080i,full hdmimode=1080i cvbsmode=576cvbs androidboot.firstboot=0 hdmitx=cecf bootfromsd console=ttyS0,115200n8 no_console_suspend console=tty0 consoleblank=0 systemd.show_status=auto [ 0.000000@0] cvbs trimming line = 0xa000 [ 0.000000@0] cvbs trimming.1.v5: 0xa0, 0x0 [ 0.000000@0] osd1:1 [ 0.000000@0] loaded:268435459 [ 0.000000@0] logo has been loaded [ 0.000000@0] 1080i:13 [ 0.000000@0] full:2 [ 0.000000@0] kernel get hdmimode form uboot is 1080i [ 0.000000@0] kernel get cvbsmode form uboot is 576cvbs [ 0.000000@0] hdmitx: cec: Function List: enable, one touch play, one touch standby, auto power by tv [ 0.000000@0] hdmitx: cec: HDMI aml_read_reg32(P_AO_DEBUG_REG0):0xf [ 0.000000@0] hdmitx: cec: HDMI hdmi_cec_func_config:0xf [ 0.000000@0] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000@0] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000@0] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000@0] Memory: 64MB 16MB 735MB = 815MB total [ 0.000000@0] Memory: 811320k/811320k available, 23240k reserved, 168960K highmem [ 0.000000@0] Virtual kernel memory layout: [ 0.000000@0] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000@0] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000@0] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) [ 0.000000@0] lowmem : 0xc0000000 - 0xef800000 ( 760 MB) [ 0.000000@0] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000@0] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000@0] .text : 0xc0008000 - 0xc0807674 (8190 kB) [ 0.000000@0] .init : 0xc0808000 - 0xc083ecc0 ( 220 kB) [ 0.000000@0] .data : 0xc0840000 - 0xc0897318 ( 349 kB) [ 0.000000@0] .bss : 0xc0897318 - 0xc0ac68f8 (2238 kB) [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000@0] Hierarchical RCU implementation. [ 0.000000@0] RCU debugfs-based tracing is enabled. [ 0.000000@0] NR_IRQS:256 [ 0.000000@0] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 4294967ms [ 0.000000@0] Global timer: MESON TIMER-F (c085b1c0) initialized [ 0.000000@0] Switching to timer-based delay loop [ 0.000000@0] Console: colour dummy device 80x30 [ 0.000000@0] console [tty0] enabled [ 0.000000@0] console [ttyS0] enabled [ 0.378710@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000) [ 0.388980@0] pid_max: default: 32768 minimum: 301 [ 0.394037@0] Mount-cache hash table entries: 512 [ 0.404148@0] CPU: Testing write buffer coherency: ok [ 0.404788@0] CPU0: thread -1, cpu 0, socket 2, mpidr 80000200 [ 0.409459@0] Setting up static identity map for 0xc05ce368 - 0xc05ce3c0 [ 0.416274@0] L310 cache controller enabled [ 0.420272@0] l2x0: 8 ways, 2048 sets, CACHE_ID 0x4100a0c9, Cache size: 524288 B [ 0.427664@0] AUX_CTRL 0x7ec60001, PERFETCH_CTRL 0x75000007, POWER_CTRL 0x00000000 [ 0.435814@0] TAG_LATENCY 0x00000111, DATA_LATENCY 0x00000222 [ 0.443104@1] CPU1: Booted secondary processor [ 0.443130@1] CPU1: thread -1, cpu 1, socket 2, mpidr 80000201 [ 0.443613@2] CPU2: Booted secondary processor [ 0.443636@2] CPU2: thread -1, cpu 2, socket 2, mpidr 80000202 [ 0.444102@3] CPU3: Booted secondary processor [ 0.444125@3] CPU3: thread -1, cpu 3, socket 2, mpidr 80000203 [ 0.444229@0] Brought up 4 CPUs [ 0.475825@0] SMP: Total of 4 processors activated (8.00 BogoMIPS). [ 0.482050@0] CPU: All CPU(s) started in SVC mode. [ 0.487715@0] devtmpfs: initialized [ 0.498517@0] clkrate [ xtal ] : 24000000 [ 0.498569@0] clkrate [ pll_sys ] : 792000000 [ 0.501443@0] clkrate [ pll_fixed ] : 2550000000 [ 0.506090@0] clkrate [ pll_vid ] : 366000000 [ 0.510516@0] clkrate [ pll_ddr ] : 0 [ 0.514230@0] clkrate [ a9_clk ] : 792000000 [ 0.518558@0] clkrate [ clk81 ] : 159375000 [ 0.524068@0] pinctrl core: initialized pinctrl subsystem [ 0.528721@0] regulator-dummy: no parameters [ 0.532797@0] NET: Registered protocol family 16 [ 0.542034@0] DMA: preallocated 4096 KiB pool for atomic coherent allocations [ 0.546880@0] VPU driver version: v02 [ 0.547742@0] load vpu_clk in dts: 182150000Hz(3) [ 0.552549@0] vpu_probe OK [ 0.562316@0] amlogic_gpio gpio: Probed amlogic GPIO driver [ 0.563278@0] register lm device lm-root [ 0.566315@0] register lm device lm1 [ 0.569869@0] register lm device lm0 [ 0.573700@0] Init pinux probe! [ 0.577185@0] pinmux-m8b pinmux: Probed amlogic pinctrl driver [ 0.582562@0] -------early_init_dt_init:115---------- [ 0.587208@0] tv_init_module [ 0.590097@0] major number 254 for disp [ 0.593873@0] vout_register_server [ 0.597251@0] register tv module server ok [ 0.601530@0] aml_i2c version: 20140813 [ 0.605349@0] aml_pmu_init, 458 [ 0.608368@0] call aml_dvfs_init in [ 0.612207@0] hdmitx: system: amhdmitx_init [ 0.615868@0] hdmitx: system: Ver: 2014May6 [ 0.620122@0] hdmitx: system: amhdmitx_probe [ 0.624950@0] hdmitx: system: gate/pwr cmd: 7 [ 0.628597@0] hdmitx: system: ALREADY init VIC = 5 [ 0.633376@0] hdmitx: system: gate/pwr cmd: 0 [ 0.638161@3] hdmitx: system: reset intr mask [ 0.720081@0] bio: create slab at 0 [ 0.721429@0] SCSI subsystem initialized [ 0.723206@0] usbcore: registered new interface driver usbfs [ 0.728376@0] usbcore: registered new interface driver hub [ 0.733855@0] usbcore: registered new device driver usb [ 0.739166@0] pps_core: LinuxPPS API ver. 1 registered [ 0.743958@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.753328@0] PTP clock support registered [ 0.758173@0] mode is 8,sync_duration_den=1,sync_duration_num=50 [ 0.763285@0] request vpu clk holdings: venci 106250000Hz [ 0.768644@0] TV mode 576cvbs selected. [ 0.772457@0] tvoutc_setmode[505] [ 0.775718@0] tvoutc_setmode[516] mode is 8 [ 0.779874@0] mode is: 8 [ 0.782397@0] VPU_VIU_VENC_MUX_CTRL: 0x5 [ 0.786279@0] viu chan = 1 [ 0.788964@0] VPU_VIU_VENC_MUX_CTRL: 0x5 [ 0.792870@0] config HPLL [ 0.795460@0] set_hpll_clk_out[206] clk = 1296 [ 0.810031@0] config HPLL done [ 1.820039@0] vdac open.1 = 0x1, 0x0 [ 1.820079@0] vinfo mode is: 576cvbs [ 1.821547@0] aml_logo: outputmode changed(13->8), reset osd1 scaler. [ 1.874920@0] call aml_pmu_probe_init in [ 1.875302@0] get property: use_pwm, value:0x00000001, dec: 1 [ 1.880968@0] get property: table_count, value:0x0000001d, dec: 29 [ 1.888646@0] meson_cs_dvfs_probe, table count:29, use_pwm:1, pwm controller:2 [ 1.895863@0] 0, 001c0000, 860000 [ 1.899291@0] 1, 001b0001, 870000 [ 1.902769@0] 2, 001a0002, 880000 [ 1.906217@0] 3, 00190003, 890000 [ 1.909681@0] 4, 00180004, 900000 [ 1.913174@0] 5, 00170005, 910000 [ 1.916608@0] 6, 00160006, 920000 [ 1.920082@0] 7, 00150007, 930000 [ 1.923535@0] 8, 00140008, 940000 [ 1.926998@0] 9, 00130009, 950000 [ 1.930490@0] 10, 0012000a, 960000 [ 1.933926@0] 11, 0011000b, 970000 [ 1.937389@0] 12, 0010000c, 980000 [ 1.940863@0] 13, 000f000d, 990000 [ 1.944316@0] 14, 000e000e, 1000000 [ 1.947780@0] 15, 000d000f, 1010000 [ 1.951272@0] 16, 000c0010, 1020000 [ 1.954707@0] 17, 000b0011, 1030000 [ 1.958170@0] 18, 000a0012, 1040000 [ 1.961645@0] 19, 00090013, 1050000 [ 1.965098@0] 20, 00080014, 1060000 [ 1.968561@0] 21, 00070015, 1070000 [ 1.972053@0] 22, 00060016, 1080000 [ 1.975488@0] 23, 00050017, 1090000 [ 1.978951@0] 24, 00040018, 1100000 [ 1.982426@0] 25, 00030019, 1110000 [ 1.985879@0] 26, 0002001a, 1120000 [ 1.989342@0] 27, 0001001b, 1130000 [ 1.992834@0] 28, 0000001c, 1140000 [ 1.996330@0] get pin for pwm-------- [ 2.000489@0] Advanced Linux Sound Architecture Driver Initialized. [ 2.007895@0] Switching to clocksource Timer-E [ 2.010908@0] FS-Cache: Loaded [ 2.031363@0] NET: Registered protocol family 2 [ 2.032291@0] TCP established hash table entries: 8192 (order: 4, 65536 bytes) [ 2.037638@0] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 2.044223@0] TCP: Hash tables configured (established 8192 bind 8192) [ 2.050680@0] TCP: reno registered [ 2.053929@0] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 2.060017@0] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 2.066834@0] NET: Registered protocol family 1 [ 2.071347@0] RPC: Registered named UNIX socket transport module. [ 2.077039@0] RPC: Registered udp transport module. [ 2.081910@0] RPC: Registered tcp transport module. [ 2.086737@0] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.093450@0] wifi_dev_probe [ 2.096178@0] wifi_dt : interrupt_pin=GPIOX_21 [ 2.100599@0] wifi_dt : irq_num=null [ 2.104158@0] wifi_dt : irq_trigger_type=GPIO_IRQ_HIGH [ 2.109250@0] wifi_dt : power_on_pin=GPIOAO_6 [ 2.113618@0] wifi_dt : power_on_pin2=GPIOX_11 [ 2.118004@0] interrupt_pin=118, irq_num=4, irq_trigger_type=0, power_on_pin=6,clock_32k_pin=107 [ 2.127396@0] Unpacking initramfs... [ 2.151889@0] Freeing initrd memory: 3744K [ 2.154535@0] bounce pool size: 64 pages [ 2.166286@0] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.168630@0] NFS: Registering the id_resolver key type [ 2.172000@0] Key type id_resolver registered [ 2.176200@0] Key type id_legacy registered [ 2.181991@0] msgmni has been set to 1261 [ 2.186023@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 2.191919@0] io scheduler noop registered (default) [ 2.196809@0] io scheduler deadline registered [ 2.201802@0] io scheduler cfq registered [ 2.205224@0] io scheduler fiops registered [ 2.218640@0] loop: module loaded [ 2.220941@0] tun: Universal TUN/TAP device driver, 1.6 [ 2.221544@0] tun: (C) 1999-2004 Max Krasnyansky [ 2.228551@0] ethernet base addr is fe0c0000 [ 2.232173@0] key device don't create,extenal_api_key_set_version:2052 [ 2.238600@0] ret = -22 [ 2.238600@0] print_buff= [ 2.243644@0] key device don't create,extenal_api_key_set_version:2052 [ 2.250135@0] ret = -22 [ 2.250135@0] print_buff= [ 2.255190@0] MAC address from eFuse: c4:4e:ac:08:d3:0f [ 2.260389@0] DWMAC100 [ 2.262776@0] stmmac - user ID: 0x10, Synopsys ID: 0x37 [ 2.267952@0] Normal descriptors [ 2.271273@0] Ring mode enabled [ 2.274447@0] DMA HW capability register supported [ 2.279125@0] RX Checksum Offload Engine supported (type 2) [ 2.284936@0] TX Checksum insertion supported [ 2.289339@0] Wake-Up On Lan supported [ 2.293229@0] Enable RX Mitigation via HW Watchdog Timer [ 2.314008@0] libphy: stmmac: probed [ 2.314057@0] eth%d: PHY ID 02430c54 at 0 IRQ POLL (stmmac-0:00) active [ 2.319708@0] PPP generic driver version 2.4.2 [ 2.323430@0] NET: Registered protocol family 24 [ 2.327755@0] usbcore: registered new interface driver smsc95xx [ 2.333697@0] usbcore: registered new interface driver qf9700 [ 2.339313@0] usbcore: registered new interface driver sr9600 [ 2.345419@0] usbcore: registered new interface driver usb-storage [ 2.351409@0] usbcore: registered new interface driver usbserial [ 2.357152@0] usbcore: registered new interface driver usbserial_generic [ 2.363834@0] usbserial: USB Serial support registered for generic [ 2.369965@0] usbcore: registered new interface driver pl2303 [ 2.375720@0] usbserial: USB Serial support registered for pl2303 [ 2.381932@0] mousedev: PS/2 mouse device common for all mice [ 2.387555@0] i2c /dev entries driver [ 2.391827@0] hidraw: raw HID events driver (C) Jiri Kosina [ 2.400689@0] usbcore: registered new interface driver usbhid [ 2.402191@0] usbhid: USB HID core driver [ 2.406866@0] ashmem: initialized [ 2.409786@0] logger: created 256K log 'log_main' [ 2.414497@0] logger: created 256K log 'log_events' [ 2.419286@0] logger: created 256K log 'log_radio' [ 2.424077@0] logger: created 256K log 'log_system' [ 2.428732@0] vout_init_module [ 2.431742@0] start init vout module [ 2.435345@0] create vout attribute ok [ 2.439225@0] ge2d_init [ 2.441447@0] ge2d_dev major:245 [ 2.445065@0] ge2d start monitor [ 2.447891@0] osd_init [ 2.447895@3] ge2d workqueue monitor start [ 2.454327@0] osd_probe, vinfo:c060908c [ 2.458463@0] Frame buffer memory assigned at phy:0x06100000, vir:0xf1000000, size=24576K [ 2.466204@0] osd_probe, mydef_var:c0880fa8, vinfo:c060908c [ 2.471758@0] init fbdev bpp is :32 [ 2.475185@0] ---------------clear framebuffer0 memory [ 2.549425@0] Console: switching to colour frame buffer device 240x67 [ 2.590352@0] Frame buffer memory assigned at phy:0x07900000, vir:0xf0600000, size=1024K [ 2.597656@0] osd_probe, mydef_var:c0880fa8, vinfo:c060908c [ 2.603182@0] don't find to display_size_default from mesonfb-dts [ 2.609229@0] init fbdev bpp is :16 [ 2.630178@0] osd probe ok [ 2.630571@0] enter aml_sysled_init [ 2.632636@0] aml_wdt_driver_init,306 [ 2.634450@0] ** disable watchdog [ 2.638045@0] keys=========================================== [ 2.643528@0] keys_devno=f200000 [ 2.647066@0] securitykey: device aml_keys created [ 2.651516@0] amlkeys=0 [ 2.654016@0] platform_driver_register--aml_keys_driver-------------------- [ 2.661321@0] start uart_ao_ttyS0:(irq = 122) [ 2.665103@0] register uart_ao ok [ 2.668835@0] set uart_b pinmux use pinctrl subsystem [ 2.673465@0] P_AO_RTI_PIN_MUX_REG:5861 [ 2.677270@0] start uart_b_ttyS2:(irq = 107) [ 2.681495@0] register uart_b ok [ 2.685093@0] start uart_d_ttyS4:(irq = 126) [ 2.688915@0] register uart_d ok [ 2.692473@0] dwc_otg: version 3.10a 12-MAY-2014 [ 2.696738@0] dwc_otg_driver_probe NOT match [ 2.701040@0] usb1: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108820, ctrl: fe080000 [ 2.709545@0] USB (1) use clock source: XTAL input [ 2.735504@0] Core Release: 3.10a [ 2.735647@0] Setting default values for core params [ 2.738242@0] curmode: 1, host_only: 1 [ 2.762180@0] Using Buffer DMA mode [ 2.762327@0] OTG VER PARAM: 1, OTG VER FLAG: 1 [ 2.764656@0] Working on port type = HOST [ 2.768724@0] dwc_otg lm1: DWC OTG Controller [ 2.773066@0] dwc_otg lm1: new USB bus registered, assigned bus number 1 [ 2.779669@0] dwc_otg lm1: irq 63, io mem 0x00000000 [ 2.784599@0] -------hcd->flags.d32 = 0 [ 2.788398@0] Init: Port Power? op_state=1 [ 2.792486@0] Init1: Power Port (0) [ 2.800253@0] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.809413@0] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.818981@0] usb usb1: Product: DWC OTG Controller [ 2.826756@0] usb usb1: Manufacturer: Linux 3.10.108 dwc_otg_hcd [ 2.834891@0] usb usb1: SerialNumber: lm1 [ 2.843414@1] hub 1-0:1.0: USB hub found [ 2.851107@1] hub 1-0:1.0: 1 port detected [ 2.858983@1] usb0: type: 1, speed: 0, config: 0, dma: 0, id: 1, phy: fe108800, ctrl: fe040000 [ 2.869730@1] USB (0) use clock source: XTAL input [ 2.898607@1] Core Release: 3.10a [ 2.906367@1] Setting default values for core params [ 2.914185@1] curmode: 1, host_only: 1 [ 2.942223@1] Using Buffer DMA mode [ 2.950079@1] OTG VER PARAM: 1, OTG VER FLAG: 1 [ 2.958046@1] Working on port type = HOST [ 2.966058@1] dwc_otg lm0: DWC OTG Controller [ 2.974113@1] dwc_otg lm0: new USB bus registered, assigned bus number 2 [ 2.983270@1] dwc_otg lm0: irq 62, io mem 0x00000000 [ 2.991355@1] -------hcd->flags.d32 = 0 [ 2.999466@1] Init: Port Power? op_state=1 [ 3.007610@1] Init1: Power Port (0) [ 3.015867@1] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.025505@1] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.035609@1] usb usb2: Product: DWC OTG Controller [ 3.043905@1] usb usb2: Manufacturer: Linux 3.10.108 dwc_otg_hcd [ 3.052491@1] usb usb2: SerialNumber: lm0 [ 3.061468@1] hub 2-0:1.0: USB hub found [ 3.069586@1] hub 2-0:1.0: 1 port detected [ 3.077725@2] Indeed it is in host mode hprt0 = 00021501 [ 3.078279@1] boot_device_flag : 1 [ 3.078293@1] ===========================================amlnf_init:642,nand device tree ok,dev-name:nand [ 3.078302@1] Nand PHY driver Version: 1.01.001.0006 (c) 2013 Amlogic Inc. [ 3.078310@1] amlnf_phy_init : amlnf init flag 0 [ 3.078418@1] ######STS IRQ mode for nand driver [ 3.078508@1] NAND device id: 45 de 94 93 76 50 8 4 [ 3.078520@1] detect NAND device: A serials NAND 8GiB SDTNRGAMA-008G [ 3.125509@1] AML_NAND_NEW_OOB : new oob [ 3.125519@1] bus_cycle=6, bus_timing=8,system=4.7ns,flash->T_REA =20,flash->T_RHOH=25 [ 3.125525@1] boot_device_flag = 1 [ 3.127586@1] NAND CKECK : arg nbbt: arg_valid= 1, valid_blk_addr = 5, valid_page_addr = 0 [ 3.134561@1] NAND CKECK : arg ncnf: arg_valid= 1, valid_blk_addr = 7, valid_page_addr = 0 [ 3.135258@1] nand shipped bbt at block 6 [ 3.167139@1] NAND CKECK : arg nkey: arg_valid= 1, valid_blk_addr = 4, valid_page_addr = 1 [ 3.167843@1] i=0,register --- nand_key [ 3.204346@1] NAND CKECK : arg nenv: arg_valid= 1, valid_blk_addr = 9, valid_page_addr = 40 [ 3.207722@1] nand adjust phy offset : block 4 [ 3.207740@1] nand adjust phy offset : block 4 [ 3.207772@1] nfboot : offset: 0x000000000000 -0x000001000000 : partitons 0 : single_chip single_plane [ 3.207779@1] nfcache : offset: 0x00000d000000 -0x000026000000 : partitons 1 : single_chip multi_plane [ 3.207785@1] nfcode : offset: 0x000033000000 -0x000057000000 : partitons 5 : single_chip multi_plane [ 3.207791@1] nfdata : offset: 0x00008a000000 -0x000176000000 : partitons 1 : single_chip multi_plane [ 3.207907@1] bad block count = 0 [ 3.207907@1] [ 3.209768@1] bad block count = 0 [ 3.209768@1] [ 3.214044@1] bad block count = 0 [ 3.214044@1] [ 3.232424@1] bad block count = 0 [ 3.232424@1] [ 3.232428@1] amlnand_add_nftl: [ 3.232840@1] Creating 1 ntd partitions [ 3.232846@1] block_num 76 [ 3.234710@1] ------init_ntd [ 3.235391@1] ntd: Giving out device 0 to nfcache [ 3.235396@1] Creating 5 ntd partitions [ 3.235403@1] block_num 174 [ 3.240160@1] ntd: Giving out device 1 to nfcode [ 3.240165@1] Creating 1 ntd partitions [ 3.240171@1] block_num 748 [ 3.258986@1] ntd: Giving out device 2 to nfdata [ 3.259863@1] boot_device_flag : 1 [ 3.259866@1] register_ntd_blktrans start [ 3.259874@1] ntd device 250! [ 3.259877@1] ntd->name: nfcache [ 3.259892@1] adjust_block_num : 4,reserved_block_ratio 10 [ 3.259900@1] nftl version 140911a [ 3.259914@1] nftl part attr 0 [ 3.261821@1] nftl start:76,12 [ 3.262085@1] first [ 3.348162@1] average_erase_count:0 [ 3.348168@1] second 8,64 [ 3.348171@1] part->max_discard_block = 4 [ 3.358679@1] all block full!! [ 3.358681@1] all discard block full!! [ 3.358689@1] free list: [ 3.358694@1] free block cnt = 69 [ 3.358699@1] new current block is 67 [ 3.358702@1] total discard page count is 0 [ 3.358708@1] create_part_list:1235,current_used_discard_block=66,current_discard_block_used_count=17 [ 3.359281@1] unmappig_pages=15853,discarded_pages=0,mapping_pages=531 [ 3.359283@1] nftl ok! [ 3.360957@3] Enable QUEUE_FLAG_DISCARD for NFTL [ 3.361789@3] aml_nftl_add_ntd ok [ 3.361796@3] ntd device 250! [ 3.361799@3] ntd->name: nfcode [ 3.361806@3] adjust_block_num : 4,reserved_block_ratio 10 [ 3.361813@3] nftl version 140911a [ 3.361845@3] nftl part attr 0 [ 3.366114@3] size_in_blk 174; total_block 164; [ 3.366118@3] nftl start:164,19 [ 3.366547@3] first [ 3.418148@3] found discard block:47 [ 3.546762@3] average_erase_count:1 [ 3.546769@3] second 159,145 [ 3.546772@3] part->max_discard_block = 4 [ 3.754181@3] all block full!! [ 3.761812@3] currnet_discard_block1:47 [ 3.804240@3] reach the last discard page:24 [ 3.810838@3] free list: [ 3.817128@3] free block cnt = 127 [ 3.823305@3] new current block is 86 [ 3.829345@3] total discard page count is 24 [ 3.835306@3] create_part_list:1235,current_used_discard_block=47,current_discard_block_used_count=121 [ 3.846465@3] unmappig_pages=21512,discarded_pages=9460,mapping_pages=6148 [ 3.853943@3] nftl ok! [ 3.861853@3] Enable QUEUE_FLAG_DISCARD for NFTL [ 3.869079@3] Enable QUEUE_FLAG_DISCARD for NFTL [ 3.876301@3] Enable QUEUE_FLAG_DISCARD for NFTL [ 3.883302@3] Enable QUEUE_FLAG_DISCARD for NFTL [ 3.890200@3] Enable QUEUE_FLAG_DISCARD for NFTL [ 3.897007@3] aml_nftl_add_ntd ok [ 3.900714@1] usb 1-1: new high-speed USB device number 2 using dwc_otg [ 3.910288@3] ntd device 250! [ 3.916571@1] Indeed it is in host mode hprt0 = 00001101 [ 3.916577@3] ntd->name: nfdata [ 3.916591@3] adjust_block_num : 4,reserved_block_ratio 10 [ 3.916599@3] nftl version 140911a [ 3.916714@3] nftl part attr 0 [ 3.935123@3] size_in_blk 748; total_block 739; [ 3.935128@3] nftl start:739,71 [ 3.936659@3] first [ 4.161885@1] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608 [ 4.169768@1] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 4.178117@1] usb 1-1: Product: USB2.0 Hub [ 4.185876@2] hub 1-1:1.0: USB hub found [ 4.192885@2] hub 1-1:1.0: 4 ports detected [ 4.306365@3] found discard block:331 [ 4.481009@1] usb 1-1.3: new high-speed USB device number 3 using dwc_otg [ 4.582114@1] usb 1-1.3: New USB device found, idVendor=0bda, idProduct=8179 [ 4.590358@1] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 4.599121@1] usb 1-1.3: Product: 802.11n WLAN NIC [ 4.606047@1] usb 1-1.3: Manufacturer: Realtek [ 4.767371@3] average_erase_count:0 [ 4.774324@3] second 497,668 [ 4.781214@3] part->max_discard_block = 4 [ 5.438583@3] all block full!! [ 5.446700@3] currnet_discard_block1:331 [ 5.477470@3] reach the last discard page:15 [ 5.486713@3] free list: [ 5.493719@3] free block cnt = 721 [ 5.500702@3] new current block is 244 [ 5.507691@3] total discard page count is 15 [ 5.514754@3] create_part_list:1235,current_used_discard_block=331,current_discard_block_used_count=442 [ 5.531988@3] unmappig_pages=145623,discarded_pages=22586,mapping_pages=2799 [ 5.540872@3] nftl ok! [ 5.549910@3] Enable QUEUE_FLAG_DISCARD for NFTL [ 5.557962@3] aml_nftl_add_ntd ok [ 5.565139@3] init_aml_nftl end [ 5.575620@3] amvideocap_init_module [ 5.582804@3] amvideocap_probe,amvideocap [ 5.589884@3] amvideocap_dev_register buf:0ba00000,size:600000. [ 5.598060@3] Amlogic A/V streaming port init [ 5.608522@3] buffersize=262144,0,start=0 [ 5.615724@3] Subtitle stbuf alloced at 0xee400000, size = 262144 [ 5.623448@3] changed the (2) buffer size from 0 to 262144 [ 5.631275@3] init vdec memsource 7a00000->b9fffff [ 5.639007@3] [tsync_pcr_init]init success. [ 5.646616@3] regist mpeg12 codec profile [ 5.654232@3] regist mpeg4 codec profile [ 5.661613@3] amvdec_vc1 module init [ 5.669170@3] regist vc1 codec profile [ 5.676552@3] amvdec_h264 module init [ 5.684179@3] regist h264 codec profile [ 5.691530@3] amvdec_h264mvc module init [ 5.699038@3] regist hmvc codec profile [ 5.706367@3] amvdec_h265 module init [ 5.713910@3] regist hevc codec profile [ 5.721448@3] regist mjpeg codec profile [ 5.728766@3] amvdec_real module init [ 5.736129@3] regist real codec profile [ 5.743147@3] amvdec_avs module init [ 5.750443@3] amvenc_avc memory resource undefined. [ 5.757409@3] amvenc_avc memory is invaild, probe fail! [ 5.764436@3] amvenc_avc: probe of amvenc_avc.0 failed with error -14 [ 5.772580@3] jpegenc module init [ 5.780314@3] alloc_keep_buffer keep_y_addr ede00000 [ 5.787700@3] alloc_keep_buffer keep_u_addr ee500000 [ 5.794987@3] alloc_keep_buffer keep_v_addr ee480000 [ 5.802124@3] yaddr=ede00000,u_addr=ee500000,v_addr=ee480000 [ 5.809962@3] create_ge2d_work_queue video task ok [ 5.818001@3] efuse=========================================== [ 5.825808@3] efuse: device efuse created [ 5.833159@3] efuse-------------------------------------------- [ 5.840592@3] SARADC Driver init. [ 5.848093@3] __saradc_probe__ [ 6.000795@3] saradc calibration: ref_val = 507 [ 6.008007@3] saradc calibration: ref_nominal = 512 [ 6.015221@3] saradc calibration: coef = 4088 [ 6.022908@3] ir irblaster probe [ 6.030588@3] Remote Driver [ 6.037688@3] Remote platform_data g_remote_base=fe600580 [ 6.044782@3] set drvdata completed [ 6.051833@3] device_create_file completed [ 6.059604@3] input: aml_keypad as /devices/platform/meson-remote/input/input0 [ 6.068894@3] input_register_device completed [ 6.076076@3] [0xffffff00] = 0x1dd0190 [ 6.083126@3] [0xffffff04] = 0xf800ca [ 6.090020@3] [0xffffff08] = 0x82006e [ 6.096882@3] [0xffffff0c] = 0x3c0030 [ 6.103681@3] [0xffffff10] = 0x30fa0013 [ 6.110447@3] [0xffffff18] = 0x6f19000 [ 6.117176@3] [0xffffff1c] = 0xbe40 [ 6.123855@3] [0x0] = 0xfa00a0 [ 6.130486@3] [0x4] = 0xfa00a0 [ 6.137056@3] [0x8] = 0xfa00a0 [ 6.143554@3] [0xc] = 0x640030 [ 6.150012@3] [0x10] = 0x30fa0013 [ 6.156485@3] [0x18] = 0x961b800 [ 6.162903@3] [0x1c] = 0x9740 [ 6.169103@3] [0x20] = 0x104 [ 6.175115@3] [0x24] = 0x0 [ 6.180977@3] [0x28] = 0x0 [ 6.186755@3] set_remote_mode[69] [ 6.192565@3] remote config major:235 [ 6.198815@3] physical address:0x2ea88000 [ 6.204877@3] Meson KeyInput init [ 6.211009@3] GPIO Keypad Driver init. [ 6.216925@3] ==gpio_key_probe== [ 6.222717@3] reg:2620,clearmask=400040,setmask=1 [ 6.228495@3] reg:2622,clearmask=ff0000,set pin=3 [ 6.234225@3] reg:2623,clearmask=7000000,setmask=7 [ 6.239900@3] reg:2620,clearmask=800080,setmask=10001 [ 6.245523@3] reg:2622,clearmask=ff000000,set pin=3 [ 6.251132@3] reg:2623,clearmask=70000000,setmask=7 [ 6.256777@3] power key(116) registed. [ 6.256783@0] key 116 up [ 6.268324@3] input: gpio_keypad as /devices/platform/gpio_keypad.5/input/input1 [ 6.276209@3] gpio keypad register input device completed. [ 6.282112@3] gpio keypad major:234 [ 6.288540@3] spi_nor_init [ 6.294660@3] amlogic_spi_nor_probe: [ 6.300496@3] amlogic_spi->state_name:default [ 6.306619@3] AMLOGIC_SPI_NOR cc000000.spi: master is unqueued, this is deprecated [ 6.314811@3] check_storage_device : spi boot_device_flag : -1 [ 6.321084@3] spi_nor_probe [ 6.327125@3] spi_nor_probe 629 boot_device_flag 1 : do not init spi [ 6.334018@3] spi_nor: probe of apollospi:32766 failed with error -12 [ 6.341050@3] amlogic_spi_nor_probe over [ 6.347552@3] mmc driver version: 1.07, 2015-01-21: fix a bug in tuning which caused eMMC data CRC error [ 6.358219@3] host->base fe108c20 [ 6.364758@3] pdata->caps 7 [ 6.371131@3] pdata->caps2 0 [ 6.377411@3] get property: port, value:0x00000001 [ 6.384742@3] get property: ocr_avail, value:0x00200000 [ 6.392088@3] get property: f_min, value:0x000493e0 [ 6.399349@3] get property: f_max, value:0x02faf080 [ 6.406533@3] get property: f_max_w, value:0x02faf080 [ 6.413621@3] get property: max_req_size, value:0x00020000 [ 6.420655@3] get property: irq_in, value:0x00000003 [ 6.427607@3] get property: irq_out, value:0x00000005 [ 6.434475@3] get property: gpio_cd, str:CARD_6 [ 6.440826@3] get property: pinname, str:sd [ 6.446773@3] get property: jtag_pin, str:CARD_0 [ 6.453084@3] get property: card_type, value:0x00000005 [ 6.459949@3] get property: gpio_dat3, str:CARD_4 [ 6.466281@3] normal card in [ 6.510694@1] sd: mmc_rescan_try_freq: trying to init card at 400000 Hz [ 6.510721@3] reg:2620,clearmask=80008,setmask=10001 [ 6.510727@3] reg:2621,clearmask=ff000000,set pin=49 [ 6.510732@3] reg:2623,clearmask=7000,setmask=7 [ 6.510737@3] reg:2620,clearmask=200020,setmask=1 [ 6.510741@3] reg:2622,clearmask=ff00,set pin=49 [ 6.510746@3] reg:2623,clearmask=700000,setmask=7 [ 6.510992@3] pdata->caps 10f [ 6.510997@3] pdata->caps2 0 [ 6.511003@3] get property: port, value:0x00000000 [ 6.511007@3] get property: ocr_avail, value:0x00200000 [ 6.511011@3] get property: f_min, value:0x000493e0 [ 6.511015@3] get property: f_max, value:0x02faf080 [ 6.511020@3] get property: max_req_size, value:0x00020000 [ 6.511029@3] get property: pinname, str:sdio [ 6.511034@3] get property: card_type, value:0x00000003 [ 6.649375@3] sd: new high speed SDHC card at address 59b4, clock 39843750, 4-bit-bus-width [ 6.659056@3] mmcblk0: sd:59b4 SD16G 14.5 GiB [ 6.681902@3] mmcblk0: p1 p2 [ 6.760686@1] [aml_sdio_probe] aml_sdio_probe() success! [ 6.768790@2] host->base fe108e00 [ 6.775588@2] pdata->caps 80000547 [ 6.782274@2] pdata->caps2 0 [ 6.788901@2] get property: port, value:0x00000005 [ 6.796538@2] get property: ocr_avail, value:0x00200000 [ 6.804143@2] get property: f_min, value:0x000493e0 [ 6.811712@2] get property: f_max, value:0x02faf080 [ 6.819237@2] get property: max_req_size, value:0x00020000 [ 6.826768@2] get property: pinname, str:emmc [ 6.833567@2] get property: card_type, value:0x00000001 [ 6.841058@2] get property: gpio_dat3, str:BOOT_3 [ 6.848025@2] [is_emmc_exist] host->storage_flag=1, POR_BOOT_VALUE=7 [ 6.855416@2] [aml_sdhc_probe]: there is not eMMC/tsd, skip sdhc_c dts config! [ 6.900665@2] [aml_sdhc_probe] aml_sdhc_probe() success! [ 6.907747@2] [dsp]DSP start addr 0xc5e00000 [ 6.914612@2] [dsp]register dsp to char divece(257) [ 6.922335@2] amlogic audio spdif interface device init! [ 6.929247@2] name=nand_key nand_key [ 6.936701@2] register_aes_algorithm:488,new way [ 6.943484@2] unkown current key-name,key_read_show:1396 [ 6.950276@2] get keyexample fail, aml_rtc_probe:755 [ 6.957340@3] rtc clock error [ 6.964610@3] aml_rtc rtc.0: rtc core: registered aml_rtc as rtc0 [ 6.971987@3] rtc clock error [ 6.978776@3] rtc clock error [ 6.985458@3] rtc clock error [ 6.992051@3] rtc clock error [ 6.998516@3] rtc clock error [ 7.004862@3] rtc clock error [ 7.011010@3] rtc clock error [ 7.016947@3] rtc clock error [ 7.022846@3] rtc clock error [ 7.028727@3] rtc clock error [ 7.034544@3] rtc clock error [ 7.042875@0] amaudio2: device amaudio2 created [ 7.048977@0] Amlogic CEC Driver, (c) 2016 Gerald Dachs, Version: 0.0.1 [ 7.056430@0] Error: Didn't get power valid value --- wifi_power_probe 323 [ 7.063809@0] wifi_power power_gpio is 6 [ 7.069927@0] wifi_power power_gpio2 is 108 [ 7.077203@0] UMP: UMP device driver -98da7b2 loaded [ 7.083955@0] aml_aes aml_aes: Aml AES [ 7.090889@0] aml_tdes aml_tdes: Aml TDES [ 7.098462@0] enter rt5616_modinit [ 7.105581@0] == ES8323 == es8323_modinit() [ 7.112780@0] i2s get no clk src setting in dts, use the default mpll 0 [ 7.120178@0] [aml-i2s-dai]enterd aml_i2s_dai_probe,old_samplerate:0,sample_rate=48000 [ 7.129531@0] [aml-spdif-dai]enter aml_dai_spdif_init [ 7.136114@0] [aml-spdif-dai]enterd aml_spdif_play,set_clock:-1,sample_rate=4 [ 7.144114@0] audio_set_958_clk, freq=4, [ 7.150621@0] IEC958 16bit [ 7.157134@0] hdmitx: audio: aout notify rate 48000 [ 7.163708@0] hdmitx: audio: aout notify size 16 [ 7.170214@0] hdmitx: audio: aout notify format CT_PCM [ 7.176859@3] [aml-spdif-dai]aml_spdif_probe [ 7.183722@0] test codec rt5616 [ 7.190301@0] test_codec_of_node, node rt5616 disable [ 7.196910@0] test codec rt5631 [ 7.203494@0] test_codec_of_node, node rt5631 disable [ 7.210188@0] test codec wm8960 [ 7.216877@0] test_codec_of_node, node wm8960 disable [ 7.223660@0] test codec dummy_codec [ 7.230413@0] test_codec_of_node, node dummy_codec disable [ 7.237259@0] no external codec, using aml default codec [ 7.244343@2] enter spdif_dit_probe [ 7.250973@2] aml_spdif_unmute [ 7.257935@2] codec_name = aml_m8_codec.0 [ 7.265353@2] p_aml_audio->hp_disable=1 [ 7.271909@2] falied to get spk event delay time paraments from dts file [ 7.279618@2] spk_event delay_time = 0 [ 7.287331@2] aml-i2s 0:playback preallocate_dma_buffer: area=f0701000, addr=2de00000, size=524288 [ 7.297907@2] aml-i2s 1:capture preallocate_dma_buffer: area=f0783000, addr=2dca0000, size=65536 [ 7.308164@2] aml_snd_m8 aml_m8_sound_card.4: AML-M8 <-> aml-i2s-dai.0 mapping ok [ 7.318486@2] aml-i2s 0:playback preallocate_dma_buffer: area=f07a4000, addr=2df00000, size=524288 [ 7.329536@2] aml-i2s 1:capture preallocate_dma_buffer: area=f0826000, addr=2dea0000, size=65536 [ 7.340238@2] aml_snd_m8 aml_m8_sound_card.4: dit-hifi <-> aml-spdif-dai.0 mapping ok [ 7.352148@2] -----ext_codec=0--- [ 7.359801@2] =aml_m8_pinmux_init==,aml_m8_pinmux_init done,---0 [ 7.368634@3] TCP: cubic registered [ 7.377449@3] NET: Registered protocol family 10 [ 7.386205@3] NET: Registered protocol family 17 [ 7.393893@3] Key type dns_resolver registered [ 7.402249@3] VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1 [ 7.410857@3] Registering SWP/SWPB emulation handler [ 7.418538@3] enter meson_pm_init [ 7.426357@3] enter meson_pm_probe! [ 7.433950@3] meson_pm_probe done ! [ 7.441504@3] AO cpu runs ok. [ 7.450821@3] regulator-dummy: disabling [ 7.458958@0] console [netcon0] enabled [ 7.466421@0] netconsole: network logging started [ 7.474007@0] rtc clock error [ 7.481483@0] aml_rtc rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0) [ 7.491131@0] meson_cpufreq: no voltage_control prop [ 7.498915@0] voltage_control = 0 [ 7.507997@0] buf[0]=f4,buf[1]=af,err=4 [ 7.512167@0] adc=383,TS_C=20,flag=1 [ 7.516297@0] efuse_flag=a [ 7.520431@0] amlogic_thermal_probe, this chip is trimmed, use thermal [ 7.525573@0] amlogic-thermal aml_thermal: amlogic thermal probe start [ 7.532081@0] #thermal-cells=7 [ 7.536414@0] pdata->temp_trip_count=7 [ 7.540755@0] temperature=60000 on trip point=0 [ 7.545070@0] fixing high_freq=1536001 to 1536000 at trip point 0,level=0 [ 7.552139@0] fixing low_freq=1536001 to 1536000 at trip point 0,level=0 [ 7.558769@0] gpu[0].gpu_high_freq=511,tmp_level[0].gpu_high_freq=511 [ 7.563943@0] cpu[0] core num==3 [ 7.568298@0] gpu[0] core num==2 [ 7.572633@0] temperature=65000 on trip point=1 [ 7.576978@0] fixing high_freq=1488001 to 1488000 at trip point 1,level=1 [ 7.584099@0] fixing low_freq=1488001 to 1488000 at trip point 1,level=1 [ 7.590799@0] gpu[1].gpu_high_freq=426,tmp_level[1].gpu_high_freq=426 [ 7.596014@0] cpu[1] core num==3 [ 7.600367@0] gpu[1] core num==2 [ 7.604658@0] temperature=70000 on trip point=2 [ 7.608948@0] fixing high_freq=1320001 to 1296000 at trip point 2,level=3 [ 7.615988@0] fixing low_freq=1320001 to 1296000 at trip point 2,level=3 [ 7.622666@0] gpu[2].gpu_high_freq=328,tmp_level[2].gpu_high_freq=328 [ 7.627807@0] cpu[2] core num==2 [ 7.632199@0] gpu[2] core num==2 [ 7.636548@0] temperature=75000 on trip point=3 [ 7.640915@0] fixing high_freq=1200001 to 1200000 at trip point 3,level=4 [ 7.648030@0] fixing low_freq=1200001 to 1200000 at trip point 3,level=4 [ 7.654747@0] gpu[3].gpu_high_freq=328,tmp_level[3].gpu_high_freq=328 [ 7.660000@0] cpu[3] core num==2 [ 7.664459@0] gpu[3] core num==1 [ 7.668872@0] temperature=80000 on trip point=4 [ 7.673342@0] fixing high_freq=1008001 to 1008000 at trip point 4,level=6 [ 7.680518@0] fixing low_freq=1008001 to 1008000 at trip point 4,level=6 [ 7.687216@0] gpu[4].gpu_high_freq=328,tmp_level[4].gpu_high_freq=328 [ 7.692552@0] cpu[4] core num==2 [ 7.697051@0] gpu[4] core num==1 [ 7.701536@0] temperature=90000 on trip point=5 [ 7.706039@0] fixing high_freq=720001 to 696000 at trip point 5,level=9 [ 7.713247@0] fixing low_freq=720001 to 696000 at trip point 5,level=9 [ 7.719708@0] gpu[5].gpu_high_freq=251,tmp_level[5].gpu_high_freq=251 [ 7.725047@0] cpu[5] core num==1 [ 7.729513@0] gpu[5] core num==1 [ 7.733921@0] temperature=260000 on trip point=6 [ 7.738271@0] fixing high_freq=-1 to -22 at trip point 6,level=-1 [ 7.744964@0] fixing low_freq=-1 to -22 at trip point 6,level=-1 [ 7.750914@0] gpu[6].gpu_high_freq=-1,tmp_level[6].gpu_high_freq=-1 [ 7.755786@0] cpu[6] core num==-1 [ 7.759981@0] gpu[6] core num==-1 [ 7.764127@0] idle interval=1000 [ 7.768224@0] pdata->name:aml_thermal [ 7.772961@0] tmp_trip[0].cpu_core_upper=1 [ 7.777147@0] tmp_trip[1].cpu_core_upper=1 [ 7.781290@0] tmp_trip[2].cpu_core_upper=2 [ 7.785320@0] tmp_trip[3].cpu_core_upper=2 [ 7.789260@0] tmp_trip[4].cpu_core_upper=2 [ 7.793204@0] tmp_trip[5].cpu_core_upper=3 [ 7.797097@0] tmp_trip[6].cpu_core_upper=-1 [ 7.800987@0] aml_thermal bind thermal-cpucore-0 okay ! [ 7.805375@0] aml_thermal bind thermal-cpufreq-0 okay ! [ 7.810686@0] amlogic: Kernel Thermal management registered [ 7.816050@0] amlogic-thermal aml_thermal: amlogic thermal probe done [ 7.822685@0] ALSA device list: [ 7.826588@0] #0: AML-M8AUDIO [ 7.830769@0] Freeing unused kernel memory: 216K LibreELEC:~ #